参数资料
型号: FSA9288AUMX
厂商: Fairchild Semiconductor
文件页数: 29/30页
文件大小: 0K
描述: IC USB MULTIMEDIA SWITCH 20-UMLP
标准包装: 5,000
功能: USB 开关
电路: 3:1
电压电源: 单电源
电压 - 电源,单路/双路(±): 3 V ~ 4.4 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 20-UFQFN 裸露焊盘
供应商设备封装: 20-UMLP(4x3)
包装: 带卷 (TR)
2009 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FSA9280A Rev 1.1.0
8
FS
A9
2
80A
US
B
Po
rt
Mu
lt
im
edia
Swi
tc
h
,
Fea
turi
n
g
Automatic
Se
lect
a
nd
Ac
ces
s
ory
Detection
4. Configuration
FSA9280A
requires
minimal
configuration
for
proper
detection and reporting. The following steps can be followed
for full configuration. In many cases, only Step 5 needs to be
implemented for proper operation.
1.
Write Control register (02h) to configure different
switching configurations and wait timing.
2.
Write Interrupt Mask 1 and 2 registers (05h, 06h) to
mask any interrupts not required in the application.
3.
Write Timing Set 1 (08h) register to program required
key-press timing and ADC-detection timing.
4.
Write Timing Set 2 (09h) register to program required
Switching Wait timing and Long Key Press timing.
5.
Write Control register (02h) to clear INT Mask bit. This
enables interrupts to the baseband.
5. Detection
The FSA9280A detection algorithms monitor both the VBUS
and ID pins of the USB interface. Based on the detection
results, multiple registers are updated and the INTB pin is
asserted to indicate to the baseband processor that an
accessory was detected and to read the registers for the
complete information.
The detection algorithm allows the application to control the
timing of the detection algorithm and the configuration of the
internal switches. The flow diagram in Figure 7 shows the
operation of the detection algorithm.
Figure 7.
Detection Flow Chart
FSA9280A Standby
Mode
Accessory Plug-in
FSA9280A Detects
Accessory Type
Is
Accessory
detected a
USB or
Factory
Mode
Set INTB Pin LOW (INT
MASK bit must have been
cleared by P)
VDDIO
=0V ?
P reads FSA9280A
Interrupt Registers
FSA9280A waits
Switching Wait time
FSA9280A auto-
conf igures switch
paths
FSA9280A Writes Device
Type registers and Attach
Interrupt
FSA9280A Writes Device
Type registers and Attach
Interrupt
FSA9280A set INTB Pin
LOW (INT MASK bit must
have been cleared by P)
P reads FSA9280A
Interrupt Registers
Wait
Bit = 1
?
FSA9280A takes no
action until Wait bit is
set HIGH by
processor
Manual
Switch =
1 ?
FSA9280A auto-
conf igures switch
paths
FSA9280A conf igures
switches according to
Manual SW 1 /2
registers
Detach
?
FSA9280A writes
Detach Interrupt and
clears Device Type
register
FSA9280A set s
INTB Pin LOW (INT
MASK bit must have
been cleared by P)
Detach
?
FSA9280A writes
Detach Interrupt
FSA9280A sets INTB
Pin LOW (INT MASK
bit must have been
cleared by P)
YES
NO
相关PDF资料
PDF描述
FSAL200QSC IC MUX/DEMUX QUAD 2X1 16QSOP
FSAV330QSC IC VIDEO SWITCH QUAD 2X1 16QSOP
FSAV331MTC IC VIDEO SWITCH DUAL 4X1 16TSSOP
FSAV430MTC IC VIDEO SWITCH QUAD 2X1 16TSSOP
FSAV433MTC IC SWITCH VIDEO 3CH 3:1 20TSSOP
相关代理商/技术参数
参数描述
FSA9485 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:USB Port Multimedia Switch Featuring Automatic Switching and Accessory Detection
FSA9485UCX 功能描述:电源开关 IC - USB Low Power Two-Input Logic Gate TinyLogic RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube
FSA95601AH 功能描述:音频放大器 SAPPHIRE DIGITAL AMP RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
FSA95601AHR2 功能描述:音频放大器 SAPPHIRE DIGITAL AMP RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel
FSA95601VAH 功能描述:音频放大器 SAPPHIRE DIGITAL AMP RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel