- 您现在的位置：买卖IC网 > PDF目录19814 > FSDM07652REWDTU (Fairchild Semiconductor)IC SWIT PWM GREEN CM HV TO220F PDF资料下载
参数资料
| 型号： | FSDM07652REWDTU |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 13/20页 |
| 文件大小： | 0K |
| 描述： | IC SWIT PWM GREEN CM HV TO220F |
| 标准包装： | 50 |
| 输出隔离： | 隔离 |
| 频率范围： | 60 ~ 72kHz |
| 输入电压： | 8 V ~ 20 V |
| 输出电压： | 650V |
| 功率（瓦特）： | 80W |
| 工作温度： | 25°C ~ 150°C |
| 封装/外壳： | TO-220-6 全封装，成形引线 |
| 供应商设备封装： | TO-220F-6L（成形） |
| 包装： | 管件 |
| 产品目录页面： | 1222 (CN2011-ZH PDF) |
V DS
Power
on
Fault
occurs
Fault
removed
V FB
FSDM0565RE Rev: 00
Overload protection
6.0V
2.5V
V CC
T 12 = C FB *(6.0-2.5)/I delay
12V
8V
t
T 1
Figure 20. Overload Protection
T 2
t
FSDM0565RE Rev: 00
Normal
operation
Fault
situation
Normal
operation
3.2 Over-Voltage Protection (OVP) : If the secondary
side feedback circuit were to malfunction or a solder
Figure 19. Auto Restart Operation
3.1 Overload Protection (OLP) : Overload is defined as
the load current exceeding a pre-set level due to an
unexpected event. In this situation, the protection circuit
should be activated to protect the SMPS. Even when the
SMPS is in normal operation, the overload protection
circuit can be activated during the load transition. To
avoid this undesired operation, the overload protection
circuit is designed to be activated after a specified time
to determine whether it is a transient situation or a true
overload situation. Because of the pulse-by-pulse
current limit capability, the maximum peak current
through the SenseFET is limited, and therefore the
maximum input power is restricted with a given input
voltage. If the output consumes beyond this maximum
power, the output voltage (V O ) decreases below the set
voltage. This reduces the current through the opto-
coupler LED, which also reduces the opto-coupler
transistor current, thus increasing the feedback voltage
(V FB ). If V FB exceeds 2.5V, D1 is blocked and the 3.5μA
current source starts to charge C B slowly up to V CC . In
this condition, V FB continues increasing until it reaches
6V, when the switching operation is terminated, as
shown in Figure 20. The delay time for shutdown is the
time required to charge C B from 2.5V to 6.0V with 3.5μA.
A 10 ~ 50ms delay time is typical for most applications.
? 2006 Fairchild Semiconductor Corporation
FSDM0465RE, FSDM0565RE, FSDM07652RE Rev. 1.0.2
13
defect caused an opening in the feedback path, the
current through the opto-coupler transistor becomes
almost zero. In this event, V FB climbs in a similar manner
to the overload situation, forcing the preset maximum
current to be supplied to the SMPS until the overload
protection is activated. Because more energy than
required is provided to the output, the output voltage may
exceed the rated voltage before the overload protection
is activated, resulting in the breakdown of the devices in
the secondary side. To prevent this situation, an over-
voltage protection (OVP) circuit is employed. In general,
V CC is proportional to the output voltage and the
FSDM0x65RE uses V CC instead of directly monitoring
the output voltage. If V CC exceeds 19V, an OVP circuit is
activated, resulting in the termination of the switching
operation. To avoid undesired activation of OVP during
normal operation, V CC should be designed below 19V.
3.3 Thermal Shutdown (TSD) : The SenseFET and the
control IC are built in one package. This makes it easy
for the control IC to detect the heat generation from the
SenseFET. When the temperature exceeds ~150°C, the
thermal shutdown is activated.
4. Soft-Start : The FSDM0x65RE has an internal soft-
start circuit that increases PWM comparator inverting
input voltage, together with the SenseFET current,
slowly after it starts up. The typical soft-start time is
10ms. The pulse width to the power switching device is
progressively increased to establish the correct working
conditions for transformers, inductors, and capacitors.
The voltage on the output capacitors is progressively
increased with the intention of smoothly establishing the
required output voltage. It also helps prevent transformer
saturation and reduces the stress on the secondary
diode during start-up.
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| TAP335K016GSB | CAP TANT 3.3UF 16V 10% RADIAL |
| MAX6469TA33AD3+T | IC REG LDO 3.3V/ADJ .3A 8-TDFN |
| MAX6469TA30BD3+T | IC REG LDO 3V/ADJ .3A 8-TDFN |
| M4A5-64/32-55JC | IC CPLD ISP 4A 64MC 44PLCC |
| VE-J4H-CW-B1 | CONVERTER MOD DC/DC 52V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FSDM07652RWDTU | 功能描述:电源开关 IC - 配电 FPS FOR LCD RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FSDM07652RYDTU | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FSDM0765RB | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Green-Mode Fairchild Power Switch (FPS⑩) for Quasi-Resonant Operation - Low EMI and High Efficiency |
| FSDM08D9002 | 制造商:Baumer Electric Ag 功能描述: |
| FSDM08D9002/S35 | 制造商:Baumer Electric Ag 功能描述: |
发布紧急采购，3分钟左右您将得到回复。