参数资料
| 型号： | FSFM261N |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 12/18页 |
| 文件大小： | 0K |
| 描述： | IC PWM/SENSEFET FPS 8-DIP |
| 标准包装： | 50 |
| 系列： | FPS™ |
| 输出隔离： | 隔离 |
| 频率范围： | 61kHz ~ 73kHz |
| 输入电压： | 9 V ~ 21 V |
| 输出电压： | 700V |
| 功率（瓦特）： | 35W |
| 工作温度： | -25°C ~ 85°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-DIP |
| 包装： | 管件 |
3.2 Over-Voltage Protection (OVP) : If the secondary
side feedback circuit malfunctions or a solder defect
causes an open in the feedback path, the current
through the opto-coupler transistor becomes almost
zero. Then, V FB climbs up in a similar manner to the
overload situation, forcing the preset maximum current
to be supplied to the SMPS until the overload protection
is activated. Because more energy than required is
provided to the output, the output voltage may exceed
the rated voltage before the overload protection is
activated, resulting in the breakdown of the devices in
the secondary side. To prevent this situation, an over-
voltage protection (OVP) circuit is employed. In general,
V CC is proportional to the output voltage and the
FSFM260/261/300 uses V CC instead of directly
monitoring the output voltage. If V CC exceeds 19V, an
OVP circuit is activated, terminating the switching
operation. To avoid undesired activation of OVP during
normal operation, V CC should be designed below 19V.
3.3 Thermal Shutdown (TSD) : The SenseFET and the
control IC are built in one package. This allows for the
control IC to detect the heat generation from the
SenseFET. When the temperature exceeds
approximately 140°C, the thermal shutdown is activated.
3.4 Abnormal Over-Current Protection (AOCP): When
the secondary rectifier diodes or the transformer pins are
shorted, a steep current with extremely high di/dt can
flow through the SenseFET during the LEB time. Even
though the FPS has overload protection, it is not enough
to protect the FPS in those abnormal cases, since
severe current stress is imposed on the SenseFET until
OLP triggers. This IC has an internal AOCP circuit
shown in Figure 21. When the gate turn-on signal is
applied to the power SenseFET, the AOCP block is
enabled and monitors the current through the sensing
resistor. The voltage across the resistor is compared with
a preset AOCP level. If the sensing resistor voltage is
greater than the AOCP level, the set signal is applied to
the latch, resulting in the shutdown of the SMPS.
OSC
4. Soft-Start : The FSFM260/261/300 has an internal
soft- start circuit that increases PWM comparator
inverting input voltage, together with the SenseFET
current, slowly after it starts up. The typical soft-start time
is 15ms. The pulse width to the power switching device
is progressively increased to establish the correct
working conditions for transformers, inductors, and
capacitors. The voltage on the output capacitors is
progressively increased to smoothly establish the
required output voltage. It also helps prevent transformer
saturation and reduce the stress on the secondary diode
during startup.
5. Burst Operation : To minimize power dissipation in
standby mode, the FSFM260/261/300 enters burst mode
operation. As the load decreases, the feedback voltage
decreases. As shown in Figure 22, the device
automatically enters burst mode when the feedback
voltage drops below V BURL (350mV). At this point,
switching stops and the output voltages start to drop at a
rate dependent on standby current load. This causes the
feedback voltage to rise. Once it passes V BURH (500mV)
switching resumes. The feedback voltage then falls and
the process repeats. Burst mode operation alternately
enables and disables switching of the power SenseFET,
thereby reducing switching loss in standby mode.
Vo
Vo set
V FB
0.5V
0.35V
Ids
Vds
2.5R
S
Q
LEB
R
Q
Gate
driver
R
time
AOCP protection
1 GND
FSFM260 Rev: 00
T1
Switching
disabled
T2 T3
Switching
disabled
T4
V OCP
FSFM260 Rev: 00
Figure 21. Abnormal Over-Current Protection
? 2009 Fairchild Semiconductor Corporation
FSFM260N / FSFM261N / FSFM300N ? Rev. 1.0.1
12
Figure 22. Waveforms of Burst Operation
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| FSFR1600L | IC FPS POWER SWITCH 9-SIP |
| FSFR1600XSL | IC FPS PWR SWITCH 160W 9-SIPL |
| FSFR1700XSL | IC FPS PWR SWITCH 200W 9-SIPL |
| FSFR1800HSL | IC FPS HALF BRIDGE RES CONV 9SIP |
| FSFR1800XS | IC FPS PWR SWITCH 260W 9-SIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FSFM300N | 功能描述:电流型 PWM 控制器 30W FPS RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| FSFP502Y | 制造商:Panduit Corp 功能描述:FIBER PLENUM ZIPCORD,50UMINTER 制造商:Panduit Corp 功能描述:FIBER PLENUM ZIPCORD,50UMINTERCONNECT CA - Cable Rools/Shrink Tubing |
| FSFP601Y | 制造商:Panduit Corp 功能描述:FIBER PLENUM SMPLX 62.5UMINTER 制造商:Panduit Corp 功能描述:FIBER PLENUM SMPLX 62.5UMINTERCONNECT CA - Cable Rools/Shrink Tubing |
| FSFP602Y | 制造商:Panduit Corp 功能描述:FIBER PLENUM ZIPCORD 62.5INTER 制造商:Panduit Corp 功能描述:FIBER PLENUM ZIPCORD 62.5INTERCONNECT CA - Cable Rools/Shrink Tubing |
| FSFP901Y | 制造商:Panduit Corp 功能描述:FIBER PLENUM SMPLX 1.6MM SM IN 制造商:Panduit Corp 功能描述:FIBER PLENUM SMPLX 1.6MM SM INTERCONNECT - Cable Rools/Shrink Tubing |
发布紧急采购，3分钟左右您将得到回复。