- 您现在的位置：买卖IC网 > PDF目录1794 > FSL106HR (Fairchild Semiconductor)IC PWM/SEMSEFET SMPS 0.5A 8-DIP PDF资料下载
参数资料
| 型号： | FSL106HR |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 10/13页 |
| 文件大小： | 0K |
| 描述： | IC PWM/SEMSEFET SMPS 0.5A 8-DIP |
| 标准包装： | 50 |
| 系列： | FPS™ |
| 输出隔离： | 隔离 |
| 频率范围： | 90kHz ~ 110kHz |
| 输入电压： | 9 V ~ 26 V |
| 输出电压： | 650V |
| 功率（瓦特）： | 13W |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-DIP |
| 包装： | 管件 |
Abnormal Over-Current Protection (AOCP)
When the secondary rectifier diodes or the transformer
pin are shorted, a steep current with extremely high di/dt
can flow through the SenseFET during the LEB time.
Even though the FPS has OLP (Overload Protection), it
is not enough to protect the FPS in that abnormal case,
since severe current stress is imposed on the
SenseFET until OLP triggers. The FPS includes the
internal AOCP (Abnormal Over-Current Protection)
circuit shown in Figure 19. When the gate turn-on signal
is applied to the power SenseFET, the AOCP block is
enabled and monitors the current through the sensing
resistor. The voltage across the resistor is compared
with a preset AOCP level. If the sensing resistor voltage
is greater than the AOCP level, the set signal is applied
to the latch, resulting in the shutdown of the SMPS.
Figure 17. Auto-Restart Protection Waveforms
Overload Protection (OLP)
Overload is defined as the load current exceeding a pre-
set level due to an unexpected event. In this situation,
the protection circuit should be activated to protect the
SMPS. However, even when the SMPS is operating
normally, the overload protection (OLP) circuit can be
activated during the load transition or startup. To avoid
this undesired operation, the OLP circuit is designed to
be activated after a specified time to determine whether
it is a transient situation or a true overload situation.
In conjunction with the I PK current limit pin (if used), the
current-mode feedback path limits the current in the
SenseFET when the maximum PWM duty cycle is
attained. If the output consumes more than this
maximum power, the output voltage (V O ) decreases
below its rating voltage. This reduces the current
through the opto-coupler LED, which also reduces the
opto-coupler transistor current, thus increasing the
feedback voltage (V FB ). If V FB exceeds 2.4V, the
feedback input diode is blocked and the 5μA current
source (I DELAY ) starts to charge C FB slowly up to V CC . In
this condition, V FB increases until it reaches 6V, when
the switching operation is terminated, as shown in
Figure 18. The shutdown delay is the time required to
charge C FB from 2.4V to 6V with 5μA current source.
Figure 19. Abnormal Over-Current Protection
Thermal Shutdown (TSD)
The SenseFET and the control IC are integrated,
making it easier to detect the temperature of the
SenseFET. When the temperature exceeds
approximately 137°C, thermal shutdown is activated.
Over-Voltage Protection (OVP)
In the event of a malfunction in the secondary-side
feedback circuit or an open feedback loop caused by a
soldering defect, the current through the opto-coupler
transistor becomes almost zero. Then, V FB climbs up in
a similar manner to the overload situation, forcing the
preset maximum current to be supplied to the SMPS
until the overload protection is activated. Because
excess energy is provided to the output, the output
voltage may exceed the rated voltage before the
overload protection is activated, resulting in the
breakdown of the devices in the secondary side. To
prevent this situation, an over-voltage protection (OVP)
circuit is employed. In general, V CC is proportional to the
output voltage and the FPS uses V CC instead of directly
monitoring the output voltage. If V CC exceeds 24V, OVP
circuit is activated, resulting in termination of the
switching operation. To avoid undesired activation of
OVP during normal operation, V CC should be designed
to be below 24V.
Figure 18. Overload Protection (OLP)
? 2010 Fairchild Semiconductor Corporation
FSL106HR ? Rev. 1.0.1
10
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| FSL106MR | IC PWM/SEMSEFET SMPS 0.5A 8-DIP |
| FSL116HR | IC FPS SWITCH PWM/SENSEFET 8MDIP |
| FSL116LR | IC PWM/SEMSEFET SMPS 1A 8-DIP |
| FSL126HR | IC FPS SWITCH PWM/SENSEFET 8MDIP |
| FSL126MR | IC PWM/SEMSEFET SMPS 2A 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FSL106MR | 功能描述:电流型 PWM 控制器 FPS FOR LOW POWER RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| FSL110D | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:3.5A, 100V, 0.600 Ohm, Rad Hard, SEGR Resistant, N-Channel Power MOSFETs |
| FSL110D1 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:3.5A, 100V, 0.600 Ohm, Rad Hard, SEGR Resistant, N-Channel Power MOSFETs |
| FSL110D3 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:3.5A, 100V, 0.600 Ohm, Rad Hard, SEGR Resistant, N-Channel Power MOSFETs |
| FSL110D4 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:TRANSISTOR | MOSFET | N-CHANNEL | 100V V(BR)DSS | 3.5A I(D) | TO-205AF |
发布紧急采购，3分钟左右您将得到回复。