- 您现在的位置：买卖IC网 > PDF目录1794 > FSL106HR (Fairchild Semiconductor)IC PWM/SEMSEFET SMPS 0.5A 8-DIP PDF资料下载
参数资料
| 型号： | FSL106HR |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 9/13页 |
| 文件大小： | 0K |
| 描述： | IC PWM/SEMSEFET SMPS 0.5A 8-DIP |
| 标准包装： | 50 |
| 系列： | FPS™ |
| 输出隔离： | 隔离 |
| 频率范围： | 90kHz ~ 110kHz |
| 输入电压： | 9 V ~ 26 V |
| 输出电压： | 650V |
| 功率（瓦特）： | 13W |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-DIP |
| 包装： | 管件 |
Functional Description
Startup
At startup, an internal high-voltage current source
supplies the internal bias and charges the external
capacitor (C A ) connected with the V CC pin, as illustrated
in Figure 14. When V CC reaches the start voltage of 12V,
the FPS? begins switching and the internal high-
voltage current source is disabled. The FPS continues
normal switching operation and the power is provided
from the auxiliary transformer winding unless V CC goes
below the stop voltage of 8V.
Feedback Control
FSL106HR employs current-mode control, as shown in
Figure 16. An opto-coupler (such as the FOD817A) and
shunt regulator (such as the KA431) are typically used
to implement the feedback network. Comparing the
feedback voltage with the voltage across the R SENSE
resistor makes it possible to control the switching duty
cycle. When the shunt regulator reference pin voltage
exceeds the internal reference voltage of 2.5V, the opto-
coupler LED current increases, the feedback voltage V FB
is pulled down, and the duty cycle is reduced. This
typically occurs when the input voltage is increased or
the output load is decreased.
Figure 14. Startup Circuit
Figure 16. Pulse-Width-Modulation Circuit
Oscillator Block
The oscillator frequency is set internally and the FPS
has a random frequency fluctuation function. Fluctuation
of the switching frequency of a switched power supply
can reduce EMI by spreading the energy over a wider
frequency range than the bandwidth measured by the
EMI test equipment. The amount of EMI reduction is
directly related to the range of the frequency variation.
The range of frequency variation is fixed internally;
however, its selection is randomly chosen by the
combination of external feedback voltage and internal
free-running oscillator. This randomly chosen switching
frequency effectively spreads the EMI noise nearby
switching frequency and allows the use of a cost-
effective inductor instead of an AC input line filter to
satisfy the world-wide EMI requirements.
Leading-Edge Blanking (LEB)
At the instant the internal SenseFET is turned on, the
primary-side capacitance and secondary-side rectifier
diode reverse recovery typically cause a high current
spike through the SenseFET. Excessive voltage across
the R SENSE resistor leads to incorrect feedback operation
in the current-mode PWM control. To counter this effect,
the FPS employs a leading-edge blanking (LEB) circuit
( see the Figure 16 ). This circuit inhibits the PWM
comparator for a short time (t LEB ) after the SenseFET is
turned on.
Protection Circuits
The FPS has several protective functions, such as
overload protection (OLP), over-voltage protection
(OVP), output-short protection (OSP), under-voltage
lockout (UVLO), abnormal over-current protection
(AOCP), and thermal shutdown (TSD). Because these
various protection circuits are fully integrated in the IC
without external components, the reliability is improved
without increasing cost. Once a fault condition occurs,
switching is terminated and the SenseFET remains off.
This causes V CC to fall. When V CC reaches the UVLO
stop voltage, V STOP (8V), the protection is reset and the
internal high-voltage current source charges the V CC
capacitor via the V STR pin. When V CC reaches the UVLO
start voltage, V START (12V), the FPS resumes normal
operation. In this manner, the auto-restart can
alternately enable and disable the switching of the
power SenseFET until the fault condition is eliminated.
Figure 15. Frequency Fluctuation Waveform
? 2010 Fairchild Semiconductor Corporation
FSL106HR ? Rev. 1.0.1
9
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| FSL106MR | IC PWM/SEMSEFET SMPS 0.5A 8-DIP |
| FSL116HR | IC FPS SWITCH PWM/SENSEFET 8MDIP |
| FSL116LR | IC PWM/SEMSEFET SMPS 1A 8-DIP |
| FSL126HR | IC FPS SWITCH PWM/SENSEFET 8MDIP |
| FSL126MR | IC PWM/SEMSEFET SMPS 2A 8-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FSL106MR | 功能描述:电流型 PWM 控制器 FPS FOR LOW POWER RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| FSL110D | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:3.5A, 100V, 0.600 Ohm, Rad Hard, SEGR Resistant, N-Channel Power MOSFETs |
| FSL110D1 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:3.5A, 100V, 0.600 Ohm, Rad Hard, SEGR Resistant, N-Channel Power MOSFETs |
| FSL110D3 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:3.5A, 100V, 0.600 Ohm, Rad Hard, SEGR Resistant, N-Channel Power MOSFETs |
| FSL110D4 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:TRANSISTOR | MOSFET | N-CHANNEL | 100V V(BR)DSS | 3.5A I(D) | TO-205AF |
发布紧急采购，3分钟左右您将得到回复。