- 您现在的位置：买卖IC网 > PDF目录1794 > FSQ0765RSLDTU (Fairchild Semiconductor)IC PWM/SENSEFET QRC TO-220F-6L PDF资料下载
参数资料
| 型号： | FSQ0765RSLDTU |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 14/19页 |
| 文件大小： | 0K |
| 描述： | IC PWM/SENSEFET QRC TO-220F-6L |
| 标准包装： | 400 |
| 系列： | FPS™ |
| 输出隔离： | 隔离 |
| 频率范围： | 48kHz ~ 67kHz |
| 输入电压： | 9 V ~ 20 V |
| 输出电压： | 650V |
| 功率（瓦特）： | 90W |
| 工作温度： | -25°C ~ 85°C |
| 封装/外壳： | TO-220-6 成形引线 |
| 供应商设备封装： | TO-220F-6L（L 型） |
| 包装： | 管件 |
4.1 Overload Protection (OLP): Overload is defined as
the load current exceeding its normal level due to an
unexpected abnormal event. In this situation, the
protection circuit should trigger to protect the SMPS.
However, even when the SMPS is in the normal
operation, the overload protection circuit can be
triggered during the load transition. To avoid this
3R
R
OSC
PWM
LEB
250ns
S
R
Q
Q
Gate
driver
undesired operation, the overload protection circuit is
designed to trigger only after a specified time to
determine whether it is a transient situation or a true
overload situation. Because of the pulse-by-pulse
AOCP
FSQ0765R Rev.00
R sense
V OCP
2
GND
current limit capability, the maximum peak current
through the SenseFET is limited, and therefore the
maximum input power is restricted with a given input
voltage. If the output consumes more than this maximum
power, the output voltage (V O ) decreases below the set
voltage. This reduces the current through the opto-
coupler LED, which also reduces the opto-coupler
transistor current, thus increasing the feedback voltage
(V FB ). If V FB exceeds 2.5V, D1 is blocked and the 5μA
current source starts to charge CB slowly up to V CC . In
this condition, V FB continues increasing until it reaches
6V, when the switching operation is terminated, as
shown in Figure 29. The delay time for shutdown is the
time required to charge C FB from 2.5V to 6V with 5μA. A
20 ~ 50ms delay time is typical for most applications.
Figure 39. Abnormal Over-Current Protection
4.3 Output-Short Protection (OSP): If the output is
shorted, steep current with extremely high di/dt can flow
through the SenseFET during the LEB time. Such a
steep current brings high voltage stress on drain of
SenseFET when turned off. To protect the device from
such an abnormal condition, OSP is included in the FSQ-
series. It is comprised of detecting V FB and SenseFET
turn-on time. When the V FB is higher than 2V and the
SenseFET turn-on time is lower than 1.2μs, the FPS
recognizes this condition as an abnormal error and shuts
down PWM switching until V CC reaches V start again. An
abnormal condition output short is shown in Figure 31.
V FB
FSQ0765R Rev.00
Overload protection
MOSFET
Drain
Current
Rectifier
Diode
Current
Turn-off delay
I LIM
6.0V
V FB
2.5V
0
V o
D
Minimum turn-on time
1.2 μ s
t 12 = C FB *(6.0-2.5)/I delay
0
output short occurs
t 1
Figure 38. Overload Protection
t 2
t
I o
0
FSQ0765R Rev. 00
4.2 Abnormal Over-Current Protection (AOCP): When
the secondary rectifier diodes or the transformer pins are
shorted, a steep current with extremely high di/dt can
flow through the SenseFET during the LEB time. Even
though the FSQ-series has overload protection, it is not
enough to protect the FSQ-series in that abnormal case,
since severe current stress is imposed on the SenseFET
until OLP triggers. The FSQ-series has an internal
AOCP circuit shown in Figure 30. When the gate turn-on
signal is applied to the power SenseFET, the AOCP
block is enabled and monitors the current through the
sensing resistor. The voltage across the resistor is
compared with a preset AOCP level. If the sensing
resistor voltage is greater than the AOCP level, the set
signal is applied to the latch, resulting in the shutdown of
the SMPS.
? 2008 Fairchild Semiconductor Corporation
FSQ0765RS ? Rev. 1.0.2
14
Figure 40. Output Short Waveforms
4.4 Over-Voltage Protection (OVP): If the secondary-
side feedback circuit malfunctions or a solder defect
caused an open in the feedback path, the current
through the opto-coupler transistor becomes almost
zero. Then, V FB climbs up in a similar manner to the
overload situation, forcing the preset maximum current
to be supplied to the SMPS until overload protection is
activated. Because more energy than required is
provided to the output, the output voltage may exceed
the rated voltage before overload protection is activated,
resulting in the breakdown of the devices in the
secondary side. To prevent this situation, an over-voltage
protection (OVP) circuit is employed. In general, V CC is
proportional to the output voltage and the FSQ-series
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| FSQ100 | IC SWIT PWM GREEN OVP HV 8DIP |
| FSQ110 | IC SWIT PWM GREEN CM OVP 8DIP |
| FSQ211L | IC SWIT PWM GREEN UVLO HV 8SOP |
| FSQ311L | IC SWITCH FPS LOW EMI HE 8-LSOP |
| FSQ321LX | IC SWIT PWM GREEN OVP UVLO 8LSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FSQ0765RSUDTU | 功能描述:电源开关 IC - 配电 SMPS Power switch (QRC) 7A 650V RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FSQ0765RSWDTU | 功能描述:电源开关 IC - 配电 FPS For LCD RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FSQ0765RWDTU | 功能描述:电源开关 IC - 配电 SMPS Power Switch 5A 650V RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FSQ100 | 功能描述:电流型 PWM 控制器 0.55A 650V SMPS RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| FSQ100_11 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Green Mode Fairchild Power Switch (FPSa?￠) |
发布紧急采购，3分钟左右您将得到回复。