- 您现在的位置：买卖IC网 > PDF目录1794 > FSQ0765RSLDTU (Fairchild Semiconductor)IC PWM/SENSEFET QRC TO-220F-6L PDF资料下载
参数资料
| 型号： | FSQ0765RSLDTU |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 17/19页 |
| 文件大小： | 0K |
| 描述： | IC PWM/SENSEFET QRC TO-220F-6L |
| 标准包装： | 400 |
| 系列： | FPS™ |
| 输出隔离： | 隔离 |
| 频率范围： | 48kHz ~ 67kHz |
| 输入电压： | 9 V ~ 20 V |
| 输出电压： | 650V |
| 功率（瓦特）： | 90W |
| 工作温度： | -25°C ~ 85°C |
| 封装/外壳： | TO-220-6 成形引线 |
| 供应商设备封装： | TO-220F-6L（L 型） |
| 包装： | 管件 |
PCB Layout Guide
Due to the combined scheme, FPS shows better noise
immunity than a conventional PWM controller and
MOSFET discrete solution. Furthermore, internal drain
current sense eliminates noise generation caused by a
sensing resistor. There are some recommendations for
PCB layout to enhance noise immunity and suppress the
noise inevitable in power-handling components.
There are typically two grounds in the conventional
SMPS: power ground and signal ground. The power
ground is the ground for primary input voltage and
power, while the signal ground is the ground for PWM
controller. In FPS, those two grounds share the same
pin, GND. Normally the separate grounds do not share
the same trace and meet only at one point, the GND pin.
Moreover, wider patterns for both grounds decrease
resistance for large currents.
Capacitors at the V CC and FB pins should be as close as
possible to the corresponding pins to avoid noise from
the switching device. Sometimes Mylar? or ceramic
capacitors with electrolytic for V CC are better for smooth
operation. The ground of these capacitors needs to
connect to the signal ground (not power ground).
The cathode of the snubber diode should be close to the
drain pin to minimize stray inductance. The Y-capacitor
between primary and secondary should be directly
connected to the power ground of DC link to maximize
surge immunity.
Because the voltage range of feedback and sync line is
small, it is affected by the noise of the drain pin. Those
traces should not draw across or close to the drain line.
When the heat sink is connected to the ground, it should
be connected to the power ground. If possible, avoid
using jumper wires for power ground and drain.
Mylar? is a registered trademark of DuPont Teijin Films.
? 2008 Fairchild Semiconductor Corporation
FSQ0765RS ? Rev. 1.0.2
17
Figure 45. Recommended PCB Layout
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| FSQ100 | IC SWIT PWM GREEN OVP HV 8DIP |
| FSQ110 | IC SWIT PWM GREEN CM OVP 8DIP |
| FSQ211L | IC SWIT PWM GREEN UVLO HV 8SOP |
| FSQ311L | IC SWITCH FPS LOW EMI HE 8-LSOP |
| FSQ321LX | IC SWIT PWM GREEN OVP UVLO 8LSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FSQ0765RSUDTU | 功能描述:电源开关 IC - 配电 SMPS Power switch (QRC) 7A 650V RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FSQ0765RSWDTU | 功能描述:电源开关 IC - 配电 FPS For LCD RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FSQ0765RWDTU | 功能描述:电源开关 IC - 配电 SMPS Power Switch 5A 650V RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FSQ100 | 功能描述:电流型 PWM 控制器 0.55A 650V SMPS RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| FSQ100_11 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Green Mode Fairchild Power Switch (FPSa?￠) |
发布紧急采购，3分钟左右您将得到回复。