- 您现在的位置：买卖IC网 > PDF目录3765 > FT232BQ-REEL (FTDI, Future Technology Devices International Ltd)IC NEW DESIGNS REFER TO FT232RQ PDF资料下载
参数资料
| 型号： | FT232BQ-REEL |
| 厂商： | FTDI, Future Technology Devices International Ltd |
| 文件页数： | 16/34页 |
| 文件大小： | 0K |
| 描述： | IC NEW DESIGNS REFER TO FT232RQ |
| 标准包装： | 1 |
| 系列： | USBmadeEZ-UART |
| 通道数： | 1，UART |
| FIFO's： | 256 字节 |
| 规程： | RS232，RS422，RS485 |
| 电源电压： | 4.35 V ~ 5.25 V |
| 带自动流量控制功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 标准包装 |
| 其它名称： | 768-1067-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
Copyright 2011 Future Technology Devices International Limited
23
Document No.: FT_000329
FT232BL
/BQ USB UART IC Datasheet Version 2.2
Clearance No.: FTDI#
171
7.2 EEPROM Configuration
Figure 7.3 EEPROM Configuration
Figure 7.3 illustrates how to connect the FT232B to the 93C46 (93C56 or 93C66) EEPROM. EECS (pin 32)
is directly connected to the chip select (CS) pin of the EEPROM. EESK (pin 1) is directly connected to the
clock (SK) pin of the EEPROM. EEDATA (pin 2) is directly connected to the Data In (Din) pin of the
EEPROM. There is a potential condition whereby both the Data Output (Dout) of the EEPROM can drive out
at the same time as the EEDATA pin of the FT232B. To prevent potential data clash in this situation, the
Dout of the EEPROM is connected to EEDATA of the FT232B via a 2.2K resistor.
Following a power-on reset or a USB reset, the FT232B will scan the EEPROM to find out (a) if an EEPROM
is attached to the Device and (b) if the data in the device is valid. If both conditions are true, then the
FT232B will use the data in the EEPROM, otherwise it will use its built-in default values. When a valid
command is issued to the EEPROM from the FT232B, the EEPROM will acknowledge the command by
pulling its Dout pin low. In order to check for this condition, it is necessary to pull Dout high using a 10K
resistor. If the command acknowledge doesn’t happen then EEDATA will be pulled high by the 10K resistor
during this part of the cycle and the device will detect an invalid command or no EEPROM present.
There are two varieties of these EEPROM’s from many sources such as Microchip, STMicro, ISSI etc. – one
is configured as being 16 bits wide, the other is configured as being 8 bits wide. The FT232B requires
EEPROMs with a 16-bit wide configuration such as the Microchip 93LC46B
device. The EEPROM must be
capable of reading data at a 1Mb clock rate at a supply voltage of 4.35V to 5.25V. Most
available parts are capable of this.
Check the manufacturers’ data sheet to find out how to connect pins 6 and 7 of the EEPROM. Some
devices specify these as no-connect, others use them for selecting 8 / 16 bit mode or for test functions.
Some other parts have their pin out rotated by 90 . It is recommended to select the required part and its
options carefully.
It is possible to “share” the EEPROM between the FT232B and another external device such as an MCU.
However, this can only be done when the FT232B is held in the reset condition as it tri-states its EEPROM
interface at that time. A typical configuration would use four bit’s of an MCU IO Port. One bit would be
used to hold the FT232B reset (using RESET#) on power-up, the other three would connect to the EECS,
EESK and EEDATA pins of the FT232B in order to read / write data to the EEPROM at this time. Once the
MCU has read / written the EEPROM, it would take RESET# high to allow the FT232B to configure itself and
enumerate over USB.
相关PDF资料 |
PDF描述 |
|---|---|
| ATMEGA168P-20MUR | MCU AVR 16K FLASH 20MHZ 32-QFN |
| SC16IS740IPW,112 | IC UART SINGLE W/FIFO 16-TSSOP |
| ATMEGA88-15AT | MCU AVR 8K FLASH 15MHZ 32-TQFP |
| ATMEGA88V-15AT | MCU AVR 8K FLASH 15MHZ 32-TQFP |
| ATMEGA88-15AT1 | MCU AVR 8K FLASH 15MHZ 32-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FT232HL | 制造商:FTDI 制造商全称:FTDI 功能描述:FT232H Single Channel Hi-Speed USB to Multipurpose UART/FIFO IC |
| FT232HL-REEL | 功能描述:USB 接口集成电路 USB HS to UART/FIFO SPI/JTAG/I2C LQFP-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| FT232HL-TRAY | 功能描述:USB 接口集成电路 USB HS to UART/FIFO SPI/JTAG/I2C LQFP-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| FT232HQ-REEL | 功能描述:USB 接口集成电路 USB HS to UART/FIFO SPI/JTAG/I2C QFN-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| FT232HQ-TRAY | 功能描述:USB 接口集成电路 USB HS to UART/FIFO SPI/JTAG/I2C QFN-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
发布紧急采购，3分钟左右您将得到回复。