- 您现在的位置：买卖IC网 > PDF目录3765 > FT232BQ-REEL (FTDI, Future Technology Devices International Ltd)IC NEW DESIGNS REFER TO FT232RQ PDF资料下载
参数资料
| 型号： | FT232BQ-REEL |
| 厂商： | FTDI, Future Technology Devices International Ltd |
| 文件页数： | 3/34页 |
| 文件大小： | 0K |
| 描述： | IC NEW DESIGNS REFER TO FT232RQ |
| 标准包装： | 1 |
| 系列： | USBmadeEZ-UART |
| 通道数： | 1，UART |
| FIFO's： | 256 字节 |
| 规程： | RS232，RS422，RS485 |
| 电源电压： | 4.35 V ~ 5.25 V |
| 带自动流量控制功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 标准包装 |
| 其它名称： | 768-1067-6 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
Copyright 2011 Future Technology Devices International Limited
11
Document No.: FT_000329
FT232BL
/BQ USB UART IC Datasheet Version 2.2
Clearance No.: FTDI#
171
possibilities exist. For instance, it may be possible to connect the device to an SRAM configurable FPGA as
supplied by vendors such as Altera and Xilinx. The FPGA device would normally be un-configured (i.e.
have no defined function) at power-up. Application software on the PC could use Bit Bang Mode to
download configuration data to the FPGA which would define its hardware function, then after the FPGA
device is configured the FT232B can switch back into UART interface mode to allow the programmed
FPGA device to communicate with the PC over USB. This approach allows a customer to create a
“generic” USB peripheral whose hardware function can be defined under control of the application
software. The FPGA based hardware can be easily upgraded or totally changed simply by changing the
FPGA configuration data file. Application notes, software and development modules for this application
area will be available from FTDI and other 3rd parties.
PreScaler Divide By 1 Fix. The previous device had a problem when the integer part of the divisor was
set to 1. In the 2nd generation device setting the prescaler value to 1 gives a baud rate of 2 million baud
and setting it to zero gives a baud rate of 3 million baud. Non-integer division is not supported with
divisor values of 0 and 1.
Less External Support Components. As well as eliminating the RCCLK RC network, and for most
applications the need for an external reset circuit, we have also eliminated the requirement for a 100K
pull-up on EECS to select 6MHz operation. When the FT232B is being used without the configuration
EEPROM, EECS, EESK and EEDATA can now be left n/c. For circuits requiring a long reset time (where the
device is reset externally using a reset generator I.C., or reset is controlled by the IO port of a MCU,
FPGA or ASIC device) an external transistor circuit is no longer required as the 1.5k pull-up resistor on
USBDP can be wired to the RSTOUT# pin instead of to 3.3V. Note : RSTOUT# drives out at 3.3V level,
not at 5V VCC level. This is the preferred configuration for new designs.
Extended EEPROM Support. The previous generation of devices only supported EEPROM of type 93C46
(64 x 16 bit). The new devices will also work with EEPROM type 93C56 (128 x 16 bit) and 93C66 (256 x
16 bit). The extra space is not used by the device, however it is available for use by other external MCU /
logic whilst the FT232B is being held in reset.
USB 2.0 (full speed option). A new EEPROM based option allows the FT232B to return a USB 2.0
device descriptor as opposed to USB 1.1. Note : The device would be a USB 2.0 Full Speed device
(12Mb/s) as opposed to a USB 2.0 High Speed device (480Mb/s).
Multiple Device Support without EEPROM. When no EEPROM (or a blank or invalid EEPROM) is
attached to the device, the FT232B no longer gives a serial number as part of its USB descriptor. This
allows multiple devices to be simultaneously connected to the same PC. However, we still highly
recommend that EEPROM is used, as without serial numbers a device can only be identified by which hub
port in the USB tree it is connected to which can change if the end user re-plugs the device into a
different port
相关PDF资料 |
PDF描述 |
|---|---|
| ATMEGA168P-20MUR | MCU AVR 16K FLASH 20MHZ 32-QFN |
| SC16IS740IPW,112 | IC UART SINGLE W/FIFO 16-TSSOP |
| ATMEGA88-15AT | MCU AVR 8K FLASH 15MHZ 32-TQFP |
| ATMEGA88V-15AT | MCU AVR 8K FLASH 15MHZ 32-TQFP |
| ATMEGA88-15AT1 | MCU AVR 8K FLASH 15MHZ 32-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FT232HL | 制造商:FTDI 制造商全称:FTDI 功能描述:FT232H Single Channel Hi-Speed USB to Multipurpose UART/FIFO IC |
| FT232HL-REEL | 功能描述:USB 接口集成电路 USB HS to UART/FIFO SPI/JTAG/I2C LQFP-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| FT232HL-TRAY | 功能描述:USB 接口集成电路 USB HS to UART/FIFO SPI/JTAG/I2C LQFP-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| FT232HQ-REEL | 功能描述:USB 接口集成电路 USB HS to UART/FIFO SPI/JTAG/I2C QFN-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| FT232HQ-TRAY | 功能描述:USB 接口集成电路 USB HS to UART/FIFO SPI/JTAG/I2C QFN-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
发布紧急采购，3分钟左右您将得到回复。