- 您现在的位置：买卖IC网 > PDF目录3765 > FT232RQ-REEL (FTDI, Future Technology Devices International Ltd)IC USB FS SERIAL UART 32-QFN PDF资料下载
参数资料
| 型号： | FT232RQ-REEL |
| 厂商： | FTDI, Future Technology Devices International Ltd |
| 文件页数： | 7/43页 |
| 文件大小： | 0K |
| 描述： | IC USB FS SERIAL UART 32-QFN |
| 产品培训模块： | USB Introduction USB-UART Interface Solutions |
| 标准包装： | 1 |
| 系列： | USBmadeEZ-UART |
| 特点： | USB 至 UART |
| 通道数： | 1，UART |
| FIFO's： | 256 字节 |
| 规程： | RS232，RS422，RS485 |
| 电源电压： | 3.3 V ~ 5.25 V |
| 带自动流量控制功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 标准包装 |
| 产品目录页面： | 634 (CN2011-ZH PDF) |
| 配用： | 768-1023-ND - MOD USB RS232 DEV/EVAL FT232RL 768-1022-ND - MOD USB UART MINI B DEV FT232R 768-1021-ND - MOD USB UART MINI DEV FT232R 768-1019-ND - MOD USB UART DEV FT232R |
| 其它名称： | 768-1008-6 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
Copyright 2010 Future Technology Devices International Limited
15
Document No.: FT_000053
FT232R USB UART IC Datasheet Version 2.10
Clearance No.: FTDI# 38
4.2 Functional Block Descriptions
The following paragraphs detail each function within the FT232R. Please refer to the block diagram shown
in Figure 2.1
Internal EEPROM. The internal EEPROM in the FT232R is used to store USB Vendor ID (VID), Product ID
(PID), device serial number, product description string and various other USB configuration descriptors.
The internal EEPROM is also used to configure the CBUS pin functions. The FT232R is supplied with the
internal EEPROM pre-programmed as described in Section 8. A user area of the internal EEPROM is
available to system designers to allow storing additional data. The internal EEPROM descriptors can be
programmed in circuit, over USB without any additional voltage requirement. It can be programmed
using the FTDI utility software called MPROG, which can be downloaded from FTDI Utilities on the FTDI
+3.3V LDO Regulator. The +3.3V LDO regulator generates the +3.3V reference voltage for driving the
USB transceiver cell output buffers. It requires an external decoupling capacitor to be attached to the
3V3OUT regulator output pin. It also provides +3.3V power to the 1.5kΩ internal pull up resistor on
USBDP. The main function of the LDO is to power the USB Transceiver and the Reset Generator Cells
rather than to power external logic. However, it can be used to supply external circuitry requiring a
+3.3V nominal supply with a maximum current of 50mA.
USB Transceiver. The USB Transceiver Cell provides the USB 1.1 / USB 2.0 full-speed physical interface
to the USB cable. The output drivers provide +3.3V level slew rate control signalling, whilst a differential
input receiver and two single ended input receivers provide USB data in, Single-Ended-0 (SE0) and USB
reset detection conditions respectfully. This function also incorporates the internal USB series termination
resistors on the USB data lines and a 1.5kΩ pull up resistor on USBDP.
USB DPLL. The USB DPLL cell locks on to the incoming NRZI USB data and generates recovered clock
and data signals for the Serial Interface Engine (SIE) block.
Internal 12MHz Oscillator - The Internal 12MHz Oscillator cell generates a 12MHz reference clock. This
provides an input to the x4 Clock Multiplier function. The 12MHz Oscillator is also used as the reference
clock for the SIE, USB Protocol Engine and UART FIFO controller blocks.
Clock Multiplier / Divider. The Clock Multiplier / Divider takes the 12MHz input from the Internal
Oscillator function and generates the 48MHz, 24MHz, 12MHz and 6MHz reference clock signals. The 48Mz
clock reference is used by the USB DPLL and the Baud Rate Generator blocks.
Serial Interface Engine (SIE). The Serial Interface Engine (SIE) block performs the parallel to serial
and serial to parallel conversion of the USB data. In accordance with the USB 2.0 specification, it
performs bit stuffing/un-stuffing and CRC5/CRC16 generation. It also checks the CRC on the USB data
stream.
USB Protocol Engine. The USB Protocol Engine manages the data stream from the device USB control
endpoint. It handles the low level USB protocol requests generated by the USB host controller and the
commands for controlling the functional parameters of the UART in accordance with the USB 2.0
specification chapter 9.
FIFO RX Buffer (128 bytes). Data sent from the USB host controller to the UART via the USB data OUT
endpoint is stored in the FIFO RX (receive) buffer. Data is removed from the buffer to the UART transmit
register under control of the UART FIFO controller. (Rx relative to the USB interface).
FIFO TX Buffer (256 bytes). Data from the UART receive register is stored in the TX buffer. The USB
host controller removes data from the FIFO TX Buffer by sending a USB request for data from the device
data IN endpoint. (Tx relative to the USB interface).
UART FIFO Controller. The UART FIFO controller handles the transfer of data between the FIFO RX and
TX buffers and the UART transmit and receive registers.
UART Controller with Programmable Signal Inversion and High Drive. Together with the UART
FIFO Controller the UART Controller handles the transfer of data between the FIFO RX and FIFO TX
buffers and the UART transmit and receive registers. It performs asynchronous 7 or 8 bit parallel to serial
and serial to parallel conversion of the data on the RS232 (or RS422 or RS485) interface.
Control signals supported by UART mode include RTS, CTS, DSR, DTR, DCD and RI. The UART Controller
also provides a transmitter enable control signal pin option (TXDEN) to assist with interfacing to RS485
transceivers. RTS/CTS, DSR/DTR and XON / XOFF handshaking options are also supported. Handshaking
is handled in hardware to ensure fast response times. The UART interface also supports the RS232
BREAK setting and detection conditions.
相关PDF资料 |
PDF描述 |
|---|---|
| SC16C550BIA44,512 | IC UART SINGLE W/FIFO 44-PLCC |
| SC16C550BIA44,518 | IC UART SINGLE W/FIFO 44-PLCC |
| SC16IS750IPW,128 | IC UART I2C/SPI 24-TSSOP |
| SC16IS740IPW/Q900, | IC UART SINGLE W/FIFO 16-TSSOP |
| XR16L788CQ-F | IC UART 64B 3.3V OCTAL 100QFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FT232RQ-TRAY | 制造商:Future Technology Devices International (FTDI Chip) 功能描述: |
| FT-23-43 | 制造商:Amidon 功能描述:Bulk |
| FT234XD-R | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC USB SERIAL BASIC UART 12DFN 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB to Serial UART Interface |
| FT234XD-T | 功能描述:USB 接口集成电路 USB to Basic Serial UART IC RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| FT-23-77 | 制造商:Amidon 功能描述: |
发布紧急采购，3分钟左右您将得到回复。