- 您现在的位置：买卖IC网 > Datasheet目录226 > FXP1500-32G (Power-One)FRONT END AC/DC 1500W 32V Datasheet资料下载
参数资料
| 型号： | FXP1500-32G |
| 厂商： | Power-One |
| 文件页数： | 5/16页 |
| 文件大小： | 0K |
| 描述： | FRONT END AC/DC 1500W 32V |
| 标准包装： | 1 |
| 系列： | FXP1500 |
| 类型： | 标准产品 |
| 输出数： | 2 |
| 输出电压： | 32V，5V |
| 输入电压： | 85 ~ 264 VAC |
| 输出 - 1 @ 电流（最大）： | 32 VDC @ 46.9A |
| 输出 - 2 @ 电流（最大）： | 5 VDC @ 1A |
| 功率（瓦特）： | 1500W |
| 电源类型： | 开关（封闭框架） |
| 应用： | 商用 |
| 安装类型： | * |
| 尺寸/尺寸： | 12.00" L x 5.00" W x 1.60" H（305.0mm x 127.0mm x 41.0mm） |
| 工作温度： | 0°C ~ 70°C |
| 效率： | 89.5% |
| 电源（瓦特）- 最大： | 1506W |
| 批准： | CE，CSA，EN IEC，UL |
| 线路调节： | ±0.5% |
| 负载调整： | ±1% |
FXP1500-32G AC-DC Front-End
& FXR-3-32G Power Shelf Data Sheet
Controls and Indicators
Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated.
Parameter
Type 1
Conditions/Description
LED indicators :
Visual Status
Indication
FP
2
?
?
?
DC OK (green)
AC OK (green)
Fan fail & Over-temperature (amber)
I C communication
I C communication
Three lines provide up to 8 separate PSU I C addresses
I C
I C
&I C
&I C
&I C
I C
I C
I C
Setting accuracy over I C: ± 50mV at V O1 nom, ± 150 mV over setting range
I C
speed can be set to full speed or automatic control via I C command.
&I C
1
2
bus
2
bus addressing
PS present pin
PS main output
remote shutdown
Power supply OK
DC current fail
AC fail / Power down
warning
DC fail / Output
voltage fault
Critical temperature
Warning/Fan Fail
DC voltage monitoring
DC current monitoring
Active current share
interconnect
V O1 presets
V O1 voltage trimming
(margining)
Fan speed control
Fan OK/FAIL
Synchronized startup
pin
Abbreviations used:
OC[S1, S2]
OC[T1-T3]
OC[U3]
OC[R1]
FP
2
2
OC[U2]
2
OC[U4]
2
OC[U1]
2
2
2
OC[R4]
OC[T4,T5]
2
2
OC[U1]
2
OC[R5]
? Monitors alarm functions and allows control of specific parameters.
? Uses standard Philips two wire bus (SCL and SDA signal lines)
2
? Used by system to indicate a PSU is installed in a system shelf
? Contact closure to logic ground ( internal pull-down resistor of 1 k ? )
? TTL compatible signal, inhibited when open contact, high or at TTL logic “1”
? Signal referenced to logic return (LRTN)
Two position switch in series with OC signal (logical AND) allows local enable/disable; “0”
Position => PS disabled; “1” Position => PS Enabled
AC OK & DC OK & no overcurrent & no over-temperature & fans working
Reports over-current condition on main output, I O1
Provides a warning that the input power has failed at least 5 ms before the output falls out of
regulation (<90% V O1 set).
? Open collector signal with 20 mA pull-down capability, referenced to logic return (LRTN).
? AC fail will go high or open during power fail condition and will go low when input is
within the operating range.
? A Power Fail warning will turn off the front panel green AC OK LED.
Internal under-voltage and overvoltage supervision of V O1 .
? Open collector signal with 20 mA pull-down capability, referenced to logic return (LRTN).
? DC fail will go high or open if V o1 < 90% or V O1 > 110% of V O1 set, measured in front of
the ORing FETs.
? Green LED on the front panel indicates normal operation; LED will flash if in parallel
operation V O1 is OK, but the unit is disabled.
Indicates the PSU operating temperature has reached [T shut-down – 10K] Indicates if the unit is
in over-temperature shutdown.
? Open collector signal with 20 mA pull-down capability, referenced to logic return (LRTN).
? The OC-output will go low 100 ms before an over-temperature condition shuts down the
unit.
? An amber LED on the front panel indicates over-temperature or fan fail.
Monitors the main output voltage, V O1 , seen at the output connector
Accuracy is ±1% over setting range and temperature.
Monitors the output current I O1 : Accuracy ± 1% over the load range.
Line must be connected to all paralleled PSUs to allow active current share functionality
between units
Output voltage is preset per programming of T4, T5
? T4/T5 = LOW / LOW => V O1 =28VDC
? T4/T5 = LOW / HIGH = HIGH / LOW => V O1 =32VDC
? T4/T5 = HIGH / HIGH => V O1 =36VDC
Output voltage trimming Vo1: ± 2 VDC
2
Two fan speed levels automatically set depending on the internal temperature. The fan
2
Indicates if the cooling fans are operating or have failed.
Overcurrent signal which can be used for synchronous startup of units in parallel or to
recover from an overload condition.
? I C
=> Signal provided over I C communication system; detailed I C information is available from the specific model’s I C Manual
? OC[#] => Hardwired signal accessible at PSU output connector, with pin number reference
? FP => Provided by devices located on PSU Front panel
2 2 2 2
found on the Power-One web site.
2
See LED Function table for further details
BCD.00021 Rev.AA, 31-JAN -11
Page 5 of 16
相关PDF资料 |
PDF描述 |
|---|---|
| FXP6000-48-S | FRONT END 3PHASE 6000W 48V |
| FXP7000-48-S | FRONT END 3PHASE 7000W 48V |
| G-RLX | SWITCH STRGHT LVR SPST 15A SOLDR |
| G002R | SWITCH CAP RECT RED FOR PHA |
| G10,WH | BOX 4.38"X3.25"X.885" WHITE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FXP1500-32GREP | 制造商:Power-One 功能描述: |
| FXP1500-48G | 功能描述:线性和开关式电源 Front End 1500W (48V) RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度: |
| FXP1500-48S100G | 制造商:Power-One 功能描述: |
| FXP1800 | 制造商:POWER-ONE 制造商全称:Power-One 功能描述:1500 to 5400-Watt Front-End Power Solutions |
| FXP1800-48G | 功能描述:线性和开关式电源 Front End 1800W (48V) RoHS:否 制造商:TDK-Lambda 产品:Switching Supplies 开放式框架/封闭式:Enclosed 输出功率额定值:800 W 输入电压:85 VAC to 265 VAC 输出端数量:1 输出电压（通道 1）:20 V 输出电流（通道 1）:40 A 商用/医用: 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:Rack 长度: 宽度: 高度: |
发布紧急采购，3分钟左右您将得到回复。