参数资料
型号: G3NA-220B-UTU DC5-24
厂商: Omron Electronics Inc-IA Div
文件页数: 13/18页
文件大小: 0K
描述: RELAY SSR 20A 5-24VDC ZERO CROSS
其它有关文件: SSR Design Considerations
标准包装: 1
系列: G3NA
电路: SPST-NO(1 Form A)
输出类型: AC,过零
负载电流: 20A
输入电压: 5 ~ 24VDC
电压 - 负载: 19 ~ 264 V
安装类型: 底座安装或面板安装
端接类型: 螺丝端子
封装/外壳: Hockey Puck
包装: 散装
继电器类型: 继电器
其它名称: G3NA-220B-UTUDC5-24
G3NA220BUTUDC524
Operating and Storage Locations
Relationship between SSRs and Duct Height
Do not use or store the G3NA in the following locations. Doing so
may result in damage, malfunction, or deterioration of performance
characteristics.
Incorrect Example
D u ct
Countermeasure 1
50 mm max.
(A height of no
more than half
Countermeasure 2
D u ct
the SSR's height
? Do not use or store in locations subject to direct sunlight.
? Do not use in locations subject to ambient temperatures outside
the range –20 to 60 ° C.
? Do not use in locations subject to relative humidity outside the
range 45% to 85% or locations subject to condensation as the
V ertical
direction
is recommended.)
Base
Airflo w
SSR
result of severe changes in temperature.
? Do not store in locations subject to ambient temperatures outside
the range –30 to 70 ° C.
D u ct
D u ct
D u ct
? Do not use or store in locations subject to corrosive or flammable
gases.
? Do not use or store in locations subject to dust (especially iron
dust) or salts.
? Do not use or store in locations subject to shock or vibration.
Do not s u rro u nd the SSR
w ith d u cts, other w ise the
heat radiation of the SSR
w ill b e ad v ersely affected.
Use short d u cts.
If the d u cts cannot b e
shortened, place the SSR on
a metal b ase so that it is not
s u rro u nded b y the d u cts.
? Do not use or store in locations subject to exposure to water, oil, or
chemicals.
? Do not use or store in locations subject to high temperatures or
high humidity.
? Do not use or store in locations subject to salt damage.
? Do not use or store in locations subject to rain or water drops.
■ Precautions for Correct Use
Please observe the following precautions to prevent failure to oper-
ate, malfunction, or undesirable effect on product performance.
Before Actual Operation
1. The G3NA in operation may cause an unexpected accident.
Therefore it is necessary to test the G3NA under the variety of
conditions that are possible. As for the characteristics of the
G3NA, it is necessary to consider differences in characteristics
between individual SSRs.
2. Unless otherwise specified, the ratings in this catalog are tested
values in a temperature range between 15 ° C and 30 ° C, a relative
humidity range between 25% and 85%, and an atmospheric pres-
sure range between 88 and 106 kPa (standard test conditions
according to JIS C5442). It will be necessary to provide the above
conditions as well as the load conditions if the user wants to con-
firm the ratings of specific G3NAs.
Mounting Method
SSR Mounting Pitch (Panel Mounting)
D u ct
Ventilation Outside the Control Panel
Be a w are of airflo w
D u ct
Ventilation
o u tlet
(axial fan)
Air inlet
If the air inlet or air outlet has a filter, clean the filter regularly to pre-
vent it from clogging to ensure an efficient flow of air.
Do not locate any objects around the air inlet or air outlet, otherwise
the objects may obstruct the proper ventilation of the control panel.
A heat exchanger, if used, should be located in front of the SSRs to
ensure the efficiency of the heat exchanger.
? Please reduce the ambient temperature of SSRs. The rated load
current of an SSR is measured at an ambient temperature of 40 ° C.
? An SSR uses a semiconductor in the output element. This causes
the temperature inside the control panel to increase due to heating
resulting from the passage of electrical current through the load. To
restrict heating, attach a fan to the ventilation outlet or air inlet of
the control panel to ventilate the panel. This will reduce the ambient
temperature of the SSRs and thus increase reliability. (Generally,
each 10 ° C reduction in temperature will double the expected life.)
Load current (A)
5A
10 A
20 A
40 A
75 A
90 A
60 mm min.
Required number
of fans per SSR
0.08
0.16
0.31
0.62
1.2
1.44
Example: For 10 SSRs with load currents of 10 A,
0.16 x 10 = 1.6
Vertical direction
Thus, 2 fans would be required.
80 mm min.
30 mm min.
Size of fans: 92 mm 2 , Air volume: 0.7 m 3 /min,
Ambient temperature of control panel: 30 ° C
If there are other instruments that generate heat in the control panel
other than SSRs, additional ventilation will be required.
Solid State Relay
G3NA
481
相关PDF资料
PDF描述
9501-100 BLK WIRE TEST 28AWG INS FLEX 100'
G3NA-210B-UTU AC200-240 RELAY SSR 10A 200-240VAC ZERO
9500PC-1/2"X36YD TAPE DBL COATED POLYESTER 1/2"
G3NA-220B-AC200-240 RELAY SSR 20A 230VAC
A2450-B RELAY SSR AC 50A 280VAC PNL MNT
相关代理商/技术参数
参数描述
G3NA-225B 制造商:未知厂家 制造商全称:未知厂家 功能描述:
G3NA-225B AC100-120 功能描述:固态继电器-工业安装 SOLID STATE RELAY RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel
G3NA-225B AC200-240 功能描述:RELAY SSR 120VAC @25A ZERO AC IN RoHS:否 类别:继电器 >> 固态 系列:G3NA 其它有关文件:Declaration of Conformity 3D 型号:MCPCyyyyE Series.sat MCPCyyyyE Series.dwg 标准包装:10 系列:MCPC 电路:SPST-NO(1 Form A) 输出类型:AC,线性控制式 导通状态电阻:- 负载电流:25A 输入电压:8 ~ 32VDC 电压 - 负载:180 ~ 280 V 安装类型:底座安装或面板安装 端接类型:螺丝端子 封装/外壳:Hockey Puck 供应商设备封装:- 包装:散装 继电器类型:继电器 相关产品:CC1810-ND - THERMAL PAD SNGL PHASE WADHESVECC1944-ND - COPPER LUG TERMINALCC1945-ND - THERMAL PAD SINGLE PHASECC1708-ND - COPPER LUG TERMINALHS301DR-ND - HEATSINK SSR 3.0DEG C/W DIN MNTCC1793-ND - HEATSINK SSR 3.5DEG C/W DIN MNTCC1794-ND - HEATSINK SSR 5.0DEG C/W DIN MNTCC1924-ND - COVER PROTECTIVE SSR CLEAR
G3NA-225B DC5-24 功能描述:RELAY SSR 120VAC@25A ZERO DC IN RoHS:是 类别:继电器 >> 固态 系列:G3NA 标准包装:2 系列:DP 电路:SPST-NO(1 Form A) 输出类型:DC 导通状态电阻:14 毫欧 负载电流:20A 输入电压:4.5 ~ 15VDC 电压 - 负载:1 ~ 48 V 安装类型:底座安装或面板安装 端接类型:螺丝端子 封装/外壳:Hockey Puck 供应商设备封装:- 包装:散装 继电器类型:接触器 其它名称:CC1832
G3NA-225B-AC100/120 制造商:Omron Industrial Automation 功能描述:RELAY; 100/120 VAC; SOLID STATE; 25 A @ 24 VAC TO 240 VAC (19 VAC TO 264 VAC)