- 您现在的位置：买卖IC网 > PDF目录7680 > G3NA-220B-UTU DC5-24 (Omron Electronics Inc-IA Div)RELAY SSR 20A 5-24VDC ZERO CROSS PDF资料下载
参数资料
| 型号： | G3NA-220B-UTU DC5-24 |
| 厂商： | Omron Electronics Inc-IA Div |
| 文件页数： | 14/18页 |
| 文件大小： | 0K |
| 描述： | RELAY SSR 20A 5-24VDC ZERO CROSS |
| 其它有关文件： | SSR Design Considerations |
| 标准包装： | 1 |
| 系列： | G3NA |
| 电路： | SPST-NO（1 Form A） |
| 输出类型： | AC，过零 |
| 负载电流： | 20A |
| 输入电压： | 5 ~ 24VDC |
| 电压 - 负载： | 19 ~ 264 V |
| 安装类型： | 底座安装或面板安装 |
| 端接类型： | 螺丝端子 |
| 封装/外壳： | Hockey Puck |
| 包装： | 散装 |
| 继电器类型： | 继电器 |
| 其它名称： | G3NA-220B-UTUDC5-24 G3NA220BUTUDC524 |
High-capacity Heat Sink
(Y92B-P250NF)
Ratings and Characteristics of High-
capacity Heat Sink (Y92B-P250NF)
DIN-track Mounting
? Assembled DIN Tracks are heavy. Mount the DIN Tracks securely.
Be sure that the Heat Sink is securely locked to the DIN Track.
? Attach End Plates (PFP-M, order separately) to both ends of the
Units on the DIN Track to hold them in place.
? To mount a Heat Sink to a DIN Track, press down at the point indi-
cated by arrow 1 in the diagram and then press in the Heat Sink at
the point indicated by arrow 2.
Fan Ratings
Rated voltage
Operating voltage
Frequency
Rated current
(See note.)
Rated speed
(See note.)
200 V
85% to 110% of rated voltage
50/60 Hz
0.061 A at 50 Hz
0.052 A at 60 Hz
2,600 r/min at 50 Hz
3,050 r/min at 60 Hz
Note: Average values.
Thermostat Ratings
Operating temperature
Contact ratings
Approx. 90 ° C
3 A at 240 VAC or 24 VDC, resistive load
Vertical
Fan/Thermostat Characteristics
Motor type
Terminal type
Single-phase shading coil induction motor
(2-pole, open type)
Terminals
Applicable DIN Track
Mounting is possible on TE35-15Fe (IEC 60715) DIN tracks. DIN
tracks from the following manufacturers can be used.
Insulation class
Insulation
resistance
IEC class B (130 ° C)
UL class A (105 ° C)
CSA class A (105 ° C)
100 M Ω min. (at 500 VDC) between all power
supply connections and uncharged metal parts.
Manufacturer
Schneider
WAGO
PHOENIX
Thickness: 1.5 mm
AM1-DE2000
210-114 or 210-197
N35/15
Thickness: 2.3 mm
---
210-118
N35/15/15-2.3
Insulation withstand 2,000 VAC (1 minute) between all power sup-
voltage ply connections and uncharged metal parts.
Amb. operating temp. ? 30 to 70 ° C (no icing)
Amb. storage temp. ? 40 to 85 ° C (no icing)
Ambient humidity 25 to 85%
Direct Mounting
? Prepare mounting holes as shown in the diagram. Tightening
torque: 0.98 to 1.47 N ? m
64 ± 0.3
Protection
Materials
Bearings
Weight
Compliant standards
Certified standards
Impedance protection
Frame: Die-cast aluminum
Blades: Glass polycarbonate
Ball bearings
Approx. 300 g
PSE, EN/IEC 60335 (CE marking compli-
ant)
UL/CSA (pending)
130 ± 0.3
Fo u r, 4.5 dia. or M4 holes
? When mounting a Heat Sink directly, first remove the Fan Unit, then
mount the Heat Sink by itself before attaching the Fan Unit again.
(Remove the two screws shown in the following diagram.)
? Use a commercial power supply (50/60 Hz) for the Fan.
? Be sure to turn OFF the power supply and wait for the blades to
stop before inspecting the Fan.
? High-precision ball bearings are used in the fan and these may be
damaged if the Fan is dropped or otherwise subjected to shock.
The life and characteristics of the Fan will be reduced if the bear-
ings are damaged. Do not subject the Fan to shock.
? The life of the Fan depends on the ambient temperature, As a
guideline, the Fan life is 40,000 hours for continuous usage at 40°C.
Remove scre w s
Fan Unit
? Be sure there are no objects near the air vents that would restrict
air flow and no loose objects, such as electrical lines.
? The Fan is an OMRON R87F-A4A-93HP (200 VAC) Fan. Use the
same model of Fan for replacement.
? The tightening torque of the mounting screw when replacing the
Fan is 0.44 N ? m.
? Terminals equivalent to Faston #110 are used for the Fan power
supply terminals.
Heat Sink
? First, temporarily mount the Heat Sink with the bottom two screws
? Refer to the following table for the OMRON Fan power supply plug
cables (order separately).
and then attach the top two screws with the mounting bracket sand-
wiched between the Heat Sink and mounting surface. Finally,
tighten all four screws.
Cable
length
1m
2m
UL certified
R87F-PC
R87F-PC-20
Complies with Electrical Appliance
and Material Safety Law (Japan)
R87F-PCJT
R87F-PCJT-20
? Connect the ground screw hole on the fan to PE.
482
Solid State Relay
G3NA
相关PDF资料 |
PDF描述 |
|---|---|
| 9501-100 BLK | WIRE TEST 28AWG INS FLEX 100' |
| G3NA-210B-UTU AC200-240 | RELAY SSR 10A 200-240VAC ZERO |
| 9500PC-1/2"X36YD | TAPE DBL COATED POLYESTER 1/2" |
| G3NA-220B-AC200-240 | RELAY SSR 20A 230VAC |
| A2450-B | RELAY SSR AC 50A 280VAC PNL MNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| G3NA-225B | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| G3NA-225B AC100-120 | 功能描述:固态继电器-工业安装 SOLID STATE RELAY RoHS:否 制造商:Crydom 控制电压范围:4 VDC to 32 VDC 负载电压额定值:7 VDC to 72 VDC 负载电流额定值:160 A 触点形式: 输出设备:SSR 安装风格:Panel |
| G3NA-225B AC200-240 | 功能描述:RELAY SSR 120VAC @25A ZERO AC IN RoHS:否 类别:继电器 >> 固态 系列:G3NA 其它有关文件:Declaration of Conformity 3D 型号:MCPCyyyyE Series.sat MCPCyyyyE Series.dwg 标准包装:10 系列:MCPC 电路:SPST-NO（1 Form A） 输出类型:AC，线性控制式 导通状态电阻:- 负载电流:25A 输入电压:8 ~ 32VDC 电压 - 负载:180 ~ 280 V 安装类型:底座安装或面板安装 端接类型:螺丝端子 封装/外壳:Hockey Puck 供应商设备封装:- 包装:散装 继电器类型:继电器 相关产品:CC1810-ND - THERMAL PAD SNGL PHASE WADHESVECC1944-ND - COPPER LUG TERMINALCC1945-ND - THERMAL PAD SINGLE PHASECC1708-ND - COPPER LUG TERMINALHS301DR-ND - HEATSINK SSR 3.0DEG C/W DIN MNTCC1793-ND - HEATSINK SSR 3.5DEG C/W DIN MNTCC1794-ND - HEATSINK SSR 5.0DEG C/W DIN MNTCC1924-ND - COVER PROTECTIVE SSR CLEAR |
| G3NA-225B DC5-24 | 功能描述:RELAY SSR 120VAC@25A ZERO DC IN RoHS:是 类别:继电器 >> 固态 系列:G3NA 标准包装:2 系列:DP 电路:SPST-NO（1 Form A） 输出类型:DC 导通状态电阻:14 毫欧 负载电流:20A 输入电压:4.5 ~ 15VDC 电压 - 负载:1 ~ 48 V 安装类型:底座安装或面板安装 端接类型:螺丝端子 封装/外壳:Hockey Puck 供应商设备封装:- 包装:散装 继电器类型:接触器 其它名称:CC1832 |
| G3NA-225B-AC100/120 | 制造商:Omron Industrial Automation 功能描述:RELAY; 100/120 VAC; SOLID STATE; 25 A @ 24 VAC TO 240 VAC (19 VAC TO 264 VAC) |
发布紧急采购，3分钟左右您将得到回复。