- 您现在的位置：买卖IC网 > PDF目录7981 > G9EA-1 DC60 (Omron Electronics Inc-EMC Div)RELAY GEN PURPOSE SPST 60A 60V PDF资料下载
参数资料
| 型号： | G9EA-1 DC60 |
| 厂商： | Omron Electronics Inc-EMC Div |
| 文件页数： | 7/10页 |
| 文件大小： | 0K |
| 描述： | RELAY GEN PURPOSE SPST 60A 60V |
| 特色产品： | DC Power Relays Capable of Interrupting 600 A at 300 VDC |
| 标准包装： | 1 |
| 系列： | G9EA-1 |
| 继电器类型： | 通用 |
| 线圈类型： | 无锁存 |
| 线圈电流： | 86.2mA |
| 线圈电压： | 60VDC |
| 触点形式： | SPST-NO（1 A 型） |
| 触点额定值（电流）： | 60A |
| 切换电压： | 400VDC - 最小值 |
| 关闭电压（最大）： | 45 VDC |
| 关闭电压（最小）： | 4.8 VDC |
| 特点： | 密封式 - 全部 |
| 安装类型： | 底座安装 |
| 端接类型： | 导线引线 |
| 包装： | 散装 |
| 操作时间： | 50ms |
| 释放时间： | 30ms |
| 线圈功率： | 5.2 W |
| 线圈电阻： | 696 欧姆 |
| 工作温度： | -40°C ~ 70°C |
| 相关产品： | Z3293-ND - DIN RAIL ADAPTR FOR G9EA-1 RELAY P9EA-C-ND - TERMINAL COVER FOR G9EA-1 RELAY |
| 其它名称： | G9EA-1DC60 G9EA1DC60 |
Precautions
!WARNING
Take measures to prevent contact with charged parts when using
the Relay for high voltages.
■ Correct Use
Refer to the relevant catalog for common precautions.
1. Be sure to tighten all screws to the appropriate torque given
below. Loose screws may result in burning due to abnormal heat
generation during energization.
? M8 screws: 8.82 to 9.80 N·m
? M6 screws: 3.92 to 4.90 N·m
? M5 screws: 1.57 to 2.35 N·m
? M4 screws: 0.98 to 1.37 N·m
? M3.5 screws: 0.75 to 1.18 N·m
2. The G9EA and G9EC Relays’ contacts have polarity. Be sure to
perform connections with the correct polarity. If the contacts are
connected with the reverse polarity, the switching characteristics
specified in this document cannot be assured.
3. Do not drop or disassemble this Relay. Not only may the Relay fail
to meet the performance specifications, it may also result in dam-
age, electric shock, or burning.
4. Do not use these Relays in strong magnetic fields of 800 A/m or
higher (e.g., near transformers or magnets). The arc discharge
that occurs during switching may be bent by the magnetic field,
resulting in flashover or insulation faults.
5. This Relay is a device for switching high DC voltages. If it is used
for voltages exceeding the specified range, it may not be possible
to interrupt the load and burning may result. In order to prevent
fire spreading, use a configuration in which the current load can
13. The contact ratings are for resistive loads. The electrical endur-
ance with inductive loads is inferior to that of resistive loads. Con-
firm correct operation under the actual operating conditions.
14. Do not use the Relay in locations where water, solvents, chemi-
cals, or oil may come in contact with the case or terminals. Doing
so may result in deterioration of the case resin or abnormal heat-
ing due to corrosion or contamination of the terminals. Also, if
electrolyte adheres to the output terminals, electrolysis may occur
between the output terminals, resulting in corrosion of the termi-
nals or wiring disconnections.
15. Be sure to turn OFF the power and confirm that there is no resid-
ual voltage before replacing the Relay or performing wiring.
16. The distance between crimp terminals or other conductive parts
will be reduced and insulation properties will be lowered if wires
are laid in the same direction from the contact terminals. Use
insulating coverings, do not wire in the same direction, and take
other measures as required to maintain insulation properties.
17. Use either a varistor, or a diode plus Zener diode as a protective
circuit against reverse surge in the relay coil. Using a diode alone
will reduce the switching characteristics.
18. Do not tighten the screws to a torque exceeding 11 N ? m for the
M8 screws and 5 N ? m for the M5 screws.
Overtightening the contact terminals will reduce the switching per-
formance and damage the product.
19. Be sure to use the screws provided with the product for wiring coil
terminals and contact terminals. The specified tightening torque
cannot be achieved with different screws and may result in abnor-
mal heat generation when energized.
The coil’s power consumption can be reduced by using in combina-
tion with a semiconductor circuit. Consult your OMRON representa-
tive for details.
Recommended Wire Size
be interrupted in the event of emergencies.
In order to ensure safety of the system, replace the Relay on a
regular basis.
6. If the Relay is used for no-load switching, the contact resistance
may increase and so confirm correct operation under the actual
operating conditions.
7. These Relays contain pressurized gas. Even in applications with
low switching frequencies, the ambient temperature and heat
caused by arc discharge in the contacts may allow permeation of
the sealed gas, resulting in arc interruption failure.
In order to ensure safety of the system, replace Relays on a regu-
lar basis.
8. Do not use or store the Relay in a vacuum. Doing so will acceler-
ate deterioration of the sealing.
9. With this Relay, if the rated voltage (or current) is continuously
applied to the coil and contacts, and then turned OFF and imme-
diately ON again, the coil temperature, and consequently the coil
resistance, will be higher than usual. This means that the must-
operate voltage will also be higher than usual, exceeding the
rated value (“hot start”). In this case, take the appropriate counter-
measures, such as reducing the load current or restricting the
energizing time or ambient operating temperature.
10. The ripple percentage for DC relays can cause fluctuations in the
must-operate voltage or humming. For this reason, reduce the rip-
ple percentage in full-wave rectified power supply circuits by add-
ing a smoothing capacitor. Ensure that the ripple percentage is
less than 5%.
11. Ensure that a voltage exceeding the specified maximum voltage
is not continuously applied to the coil. Abnormal heating in the coil
may shorten the lifetime of the insulation coating.
12. Do not use the Relay at a switching voltage or current greater
than the specified maximum values. Doing so may result in arc
discharge interruption failure or burning due to abnormal heating
in the contacts.
Model
G9EA-1(-B)
G9EA-1(-B)-CA
Note: Use flexible leads.
Size
14 to 22 mm 2
22 to 38 mm 2
DC Power Relays (60-A, 100-A Models)
G9EA-1
7
相关PDF资料 |
PDF描述 |
|---|---|
| SY100EL04ZC | IC GATE AND/NAND 2-INPUT 8-SOIC |
| TXR18AB00-2412AI | ADPTR TINEL LOCK STR SHELL 24 |
| SY100EL01ZI TR | IC GATE OR/NOR 4-INPUT 8-SOIC |
| 74LVC74ADB,112 | IC DUAL D FF POS-EDGE 14SSOP |
| 89126-0101 | CONN 26 POS IDC SOCKET GOLD POL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| G9EA1DC60NC | 制造商:Omron Corporation 功能描述: |
| G9EB-1 | 制造商:OMRON 制造商全称:Omron Electronics LLC 功能描述:DC Power Relays (25-A Models) |
| G9EB-1-B | 制造商:OMRON 制造商全称:Omron Electronics LLC 功能描述:DC Power Relays (25-A Models) |
| G9EB-1-B DC100 | 功能描述:通用继电器 Switching/Current Conduction 250V 25A RoHS:否 制造商:Omron Electronics 触点形式:1 Form A (SPST-NO) 触点电流额定值:150 A 线圈电压:24 VDC 线圈电阻:144 Ohms 线圈电流:167 mA 切换电压:400 V 安装风格:Chassis 触点材料: |
| G9EB-1-B DC12 | 功能描述:RELAY GEN PURPOSE SPST 25A 12V RoHS:是 类别:继电器 >> 功率，高于 2 安 系列:G9EB-1 标准包装:100 系列:SNR, SCHRACK 继电器类型:通用 线圈类型:无锁存 线圈电流:7mA 线圈电压:24VDC 触点形式:SPDT（1 C 型） 触点额定值（电流）:6A 切换电压:400VAC - 最小值 关闭电压（最大）:16.8 VDC 关闭电压（最小）:1.2 VDC 特点:密封式 - 全部 安装类型:通孔 端接类型:PC 引脚 包装:散装 触点材料:银锡氧化物（AgSnO） 操作时间:12ms 释放时间:5ms 线圈功率:170 mW 线圈电阻:3.4 千欧 工作温度:-40°C ~ 85°C 相关产品:PB1591-ND - RELAY SOCKET DIN SCREW DC 其它名称:2-1393236-1 |
发布紧急采购，3分钟左右您将得到回复。