- 您现在的位置：买卖IC网 > PDF目录223854 > GL602USB-A (Electronic Theatre Controls, Inc.) USB KEYBOARD MICROCONTROLLER PDF资料下载
参数资料
| 型号： | GL602USB-A |
| 厂商： | Electronic Theatre Controls, Inc. |
| 英文描述： | USB KEYBOARD MICROCONTROLLER |
| 中文描述： | USB键盘单片机 |
| 文件页数： | 11/35页 |
| 文件大小： | 201K |
| 代理商： | GL602USB-A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
Revision 1.6
-19-
02/28/2000
4.6 USB ENGINE
The USB module contains three functional blocks: a 3.3-volt regulator, a low-speed USB transceiver, and the Serial
Interface Engine (SIE). The USB module is only enabled under USB mode. The following description is the function
of the regulator, transceiver, and SIE.
4.6.1 Voltage Regulator
The USB data lines are required by the USB specification to have a maximum output voltage between 2.8V and 3.6V.
Because the GL602USB is a low speed USB device, the D- lines also are required to have an external 1.5-k
pull-up
resistor connected between a data line and a voltage source between 3.0 V and 3.6 V. Since the power provided by the
USB cable is specified to be between 4.4V and 5.0V, an on-chip regulator is used to drop the voltage to the
appropriate level for sourcing the USB transceiver and external pull-up resistor. An output pin driven by the regulator
is provided to source the 1.5-k
external resistor.
4.6.2 USB Transceiver
The USB transceiver provides the physical interface to the USB D+ and D- data lines. The transceiver is composed of
two parts: an output driver circuit and a receiver.
The USB transceiver uses a differential output driver to drive the USB data signal onto the USB cable. The static
output swing of the driver in its low state is below the VOL of 0.3V with 1.5-k load to 3.6V and in its high state is
above the VOH of 2.8V with 15-k load to ground. The output swings between the differential high and low state are
well balanced to minimize signal skew. Slew rate control on the driver is used to minimize the radiated noise and cross
talk. The driver’s outputs support 3-state operation to achieve bi-directional half-duplex operation. The driver can
tolerate a voltage on the signal pins of –0.5V to 3.8V with respect to local ground reference without damage.
The rise and fall time of the signals on this cable are greater than 75ns to keep RFI (radio frequency interference)
emissions under FCC (Federal Communications Commission) class B limits and less than 300ns to limit timing delays,
signaling skews, and distortions. The driver reaches the specified static signal levels with smooth rise and fall times,
and minimal reflections and ringing when driving the cable. This driver is used only on segments between low-speed
devices and the ports to which they are connected.
USB data transmission is done with differential signals. A differential input receiver is used to accept the USB data
signal. A differential 1 on the bus is represented by D+ being at least 200mV more positive than D- as seen at the
receiver, and a differential 0 is represented by D- being at least 200mV more positive than D+ as seen at the receiver.
The signal cross over point must be between 1.3V and 2.0V.
The receiver features an input sensitivity of 200mV when both differential data inputs are in the range of 0.8V and
2.5V with respect to the local ground reference. This is called the common mode input voltage range. Proper data
reception also is achieved when the differential data lines are outside the common mode range. The receiver can
tolerate static input voltage between –0.5V to 3.8V with respect to its local ground reference without damage. In
addition to the differential receiver, there is a single-ended receiver for each of the two data lines.
相关PDF资料 |
PDF描述 |
|---|---|
| GL9575 | P-CHANNEL ENHANCEMENT MODE POWER MOSFET |
| GLCB03A9A5C029 | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.55A, 125VDC, PANEL MOUNT |
| GLCB04A9A1C026 | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.55A, 125VDC, PANEL MOUNT |
| GLCB04A9A1Q02 | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.55A, 125VDC, PANEL MOUNT |
| GLCB04A9A3C023 | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.55A, 125VDC, PANEL MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| GL603USB | 制造商:未知厂家 制造商全称:未知厂家 功能描述:USB + PS/2 MOUSE MICROCONTROLLER |
| GL603USB-A | 制造商:未知厂家 制造商全称:未知厂家 功能描述:USB + PS/2 MOUSE MICROCONTROLLER |
| GL603USB-B | 制造商:未知厂家 制造商全称:未知厂家 功能描述:USB + PS/2 MOUSE MICROCONTROLLER |
| GL6100 | 制造商:SIERRA WIRELESS 功能描述:MODEM KIT GPRS RS232 ANTENNA 制造商:SIERRA WIRELESS 功能描述:MODEM, GSM / GPRS, QUAD BAND, RS232 制造商:SIERRA WIRELESS 功能描述:MODEM, GSM / GPRS, QUAD BAND, RS232; Protocol:TCP / IP; Supply Voltage Min:4.75V; Supply Voltage Max:32V; Module Interface:Serial; Kit Features:Quad Band 850/900/1800/1900 MHz GSM-GPRS Class 10 Modem, CSD, Fax and SMS; Supply Voltage;RoHS Compliant: Yes |
| GL6100_1101447 | 制造商:Sierra Wireless 功能描述:2G CELLULAR GATEWAY |
发布紧急采购，3分钟左右您将得到回复。