- 您现在的位置：买卖IC网 > PDF目录60615 > GSC24BC04 (GTM CORPORATION) 2-WIRE SERIAL EEPROMS PDF资料下载
参数资料
| 型号： | GSC24BC04 |
| 厂商： | GTM CORPORATION |
| 英文描述： | 2-WIRE SERIAL EEPROMS |
| 中文描述： | 2线串行EEPROM |
| 文件页数： | 7/9页 |
| 文件大小： | 305K |
| 代理商： | GSC24BC04 |
GSC24BC01/02/02/04/08/16
Page: 7/9
ISSUED DATE :2006/06/14
REVISED DATE :
Figure 9. Byte Write
Figure 10. Page Write
(
* = DON’T CARE bit for 1K)
Write Operations
Byte/Page Write:
If a write operation is entered (R/W=0) and an acknowledgment is sent, then the next sequence requires an
8-bit data word address. After an acknowledgment is received from this word address, the 1st byte of data can
be loaded. The device will send an acknowledgment after each byte to confirm the transmission.
To being the write cycle, a STOP condition must be issued (refer to Figure 9). Both byte and page write
operations are supported, so the STOP condition can be issued after the 1st byte or the last byte in the page.
When the STOP condition occurs, an internal time is started, all input are disabled, and the EEPROM will not
respond to any more commands until the write cycle is completed.
Note: The number of bytes in a page depends on the density used. If 1K density is used, then the page size is
8 bytes. In contrast, if the 16K density is used, then the page size is 16 bites. Refer to the Memory
Organization section for more details.
The internal page counter is incremented after each byte received, but the row location of the memory page
will always remain the same. Therefore, the device will wrap around to the 1st byte in the page after the last
byte in the page is received. Any further data loaded into the page buffer will overwrite the previous data
loaded.
Acknowledge Polling: After the STOP condition is issued, the write cycle begins. Acknowledge polling can be
initiated by sending a START condition followed by the device address word. If the EEPROM has completed
the internal write cycle and returned to standby mode, the device will respond by sending back an
acknowledgment by pulling the SDA pin low. Otherwise, the sequence will be ignored and no acknowledgment
will be sent.
Read Operations
There are three types of read operations: current address read, random address read, and sequence read. A
random address read can be considered a current address read operation with an additional sequence in the
beginning to load a different address into the internal counter. A sequential read occurs when subsequent
bytes are clocked out after a current address read or random address read occurs.
*
相关PDF资料 |
PDF描述 |
|---|---|
| GSC24BC08 | 2-WIRE SERIAL EEPROMS |
| GSC24BC16 | 2-WIRE SERIAL EEPROMS |
| GSC2596M | 150 KHz, 2A PWM Step-Down DC/DC Converter |
| GSC3842 | HIGH PERFORMANCE CURRENT MODE CONTROLERS |
| GSC3843 | HIGH PERFORMANCE CURRENT MODE CONTROLERS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| GSC24BC08 | 制造商:GTM 制造商全称:GTM 功能描述:2-WIRE SERIAL EEPROMS |
| GSC24BC16 | 制造商:GTM 制造商全称:GTM 功能描述:2-WIRE SERIAL EEPROMS |
| GSC-24D/B | 制造商:Crydom 功能描述: |
| GSC25 | 制造商:SLPOWER 制造商全称:SL Power Electronics 功能描述:25 Watt Global Performance Switchers |
| GSC2596M | 制造商:GTM 制造商全称:GTM 功能描述:150 KHz, 2A PWM Step-Down DC/DC Converter |
发布紧急采购，3分钟左右您将得到回复。