- 您现在的位置：买卖IC网 > Datasheet目录438 > GW5DGC50M04 (Sharp Microelectronics)LED MOD 25WATT ZENIGATA 5000K Datasheet资料下载
参数资料
| 型号： | GW5DGC50M04 |
| 厂商： | Sharp Microelectronics |
| 文件页数： | 19/22页 |
| 文件大小： | 0K |
| 描述： | LED MOD 25WATT ZENIGATA 5000K |
| 标准包装： | 40 |
| 颜色： | 冷白色 |
| 配置： | 方形 |
| 在特定电流下的光通量 - 测试： | 2080 lm |
| 电流 - 测试： | 700mA |
| 电流 - 最大： | 1.05A |
| 带连接器： | 无 |
| 驱动器电路： | 无 |
| 波长： | 5000K |
| 电压： | 37V |
| 其它名称： | 425-2800 |
DG-10Y030D
Model No. Page
GW5DGC**M04
? Do not touch resin part including white resin part on the surface of LED.
No light emission may occur due to damage of resin or cutting wire of LEDs by outer force.
When using tweezers, please handle by ceramic substrate part and avoid touching resin part.
For mounting, please handle by side part of ceramic or the specified area shown below.
Handling area
⑤ Connecting method
In case of solder connecting method, follow the conditions mentioned below.
? Use Soldering iron with thermo controller (tip temperature 380 ℃ ), within 5 seconds per one place.
? Secure the solderwettability on whole solder pad and leads.
? During the soldering process, put the ceramic board on materials whose conductivity is poor enough
not to radiate heat of soldering.
? Warm up (with using a heated plate) the substrate is recommended before soldering.
( preheat condition: 100 ℃ ～ 150 ℃ , within 60 sec )
? Avoid touching a part of resin with soldering iron.
? This product is not designed for reflow and flow soldering.
? Avoid such lead arrangement as applying stress to solder-applied area.
? Please do not detach solder and make re-solder.
? Please solder evenly on each electrodes.
? Please prevent flux from touching to resin.
⑥ Static electricity
This product is subject to static electricity, so take measures to cope with it.
Install circuit protection device to drive circuit, if necessary.
⑦ Drive method
? Any reverse voltage cannot be applied to LEDs when they are in operation or not.
Design a circuit so that any flow of reverse or forward voltage can not be applied to LEDs
when they are out of operation.
? Module is composed of LEDs connected in both series and parallel.
Constant voltage power supply runs off more than specified current amount due to lowered V F
caused by temperature rise.
Constant current power supply is recommended to drive.
⑧ Cleaning
Avoid cleaning, since silicone resin is eroded by cleaning.
⑨ Color-tone variation
Chromaticity of this product is monitored by integrating sphere right after the operation.
Chromaticity varies depending on measuring method, light spread condition, or ambient temperature.
Please verify your actual conditions before use.
16 of 18
相关PDF资料 |
PDF描述 |
|---|---|
| GW5DLA40M04 | LED MOD 15WATT ZENIGATA 4050K |
| GW5DMC30M04 | LED MOD 25WATT ZENIGATA 3025K |
| GWM100-01X1-SMD SAM | IC FULL BRIDGE 3PH ISOPLUS SMD |
| GWM120-0075X1-SMD SAM | IC FULL BRIDGE 3PH ISOPLUS SMD |
| GWM160-0055P3 | IC FULL BRIDGE 3PH W/MOSF ISODIL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| GW5DGC65M04 | 功能描述:LED照明模块 25W Meg Zenigata 6500K 2080LM 90CRI RoHS:否 制造商:Cree, Inc. 产品:LED Modules LED 数量:1 照明颜色:Neutral White 射束角:96 deg 波长/色温:3500 K 光强度: 光通量:3000 lm 宽度: 长度:88.2 mm 系列: 封装:Bulk |
| GW5DGE27MR5 | 功能描述:大功率LED - 白色 47.5W Mega Zenigata 2700K, 3590LM, 93CRI RoHS:否 制造商:Cree, Inc. 照明颜色:Cool White 颜色温度:5000 K 光通量:280 lm 显示角:125 deg 正向电流:700 mA 正向电压:2.9 V 安装风格:SMD/SMT 系列:XMLBWW 封装:Reel |
| GW5DGE27MR5-SAMPLES | 制造商:Sharp Microelectronics Corporation 功能描述: |
| GW5DGE30MR5 | 功能描述:大功率LED - 白色 47.5W Mega Zenigata 3000K, 3670LM, 93CRI RoHS:否 制造商:Cree, Inc. 照明颜色:Cool White 颜色温度:5000 K 光通量:280 lm 显示角:125 deg 正向电流:700 mA 正向电压:2.9 V 安装风格:SMD/SMT 系列:XMLBWW 封装:Reel |
| GW5DGE30MR5-SAMPLES | 制造商:Sharp Microelectronics Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。