参数资料
| 型号： | HA3-5020-5Z |
| 厂商： | Intersil |
| 文件页数： | 3/23页 |
| 文件大小： | 0K |
| 描述： | IC AMP VIDEO CFA 100MHZ 8-DIP |
| 标准包装： | 50 |
| 应用： | 电流反馈 |
| 电路数： | 1 |
| -3db带宽： | 100MHz |
| 转换速率： | 1100 V/µs |
| 电流 - 电源： | 7.5mA |
| 电流 - 输出 / 通道： | 31.7mA |
| 电压 - 电源，单路/双路(±)： | ±4.5 V ~ 18 V |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
| 产品目录页面： | 1234 (CN2011-ZH PDF) |
11
FN2845.12
May 21, 2013
Referring to Figure 7, it can be seen that R6 will act as a pull-up
resistor to +VCC if the DISABLE pin is left open. In those cases
where the enable/disable function is not required on all circuits
some circuits can be permanently enabled by letting the
DISABLE pin float. If a driver is used to set the enable/disable
level, be sure that the driver does not sink more than 20
μA
when the DISABLE pin is at a high level. TTL gates, especially
CMOS versions, do not violate this criteria so it is permissible to
control the enable/disable function with TTL.
Typical Applications
Two Channel Video Multiplexer
Referring to the amplifier U1A in Figure 8, R1 terminates the
cable in its characteristic impedance of 75
Ω, and R
4 back
terminates the cable in its characteristic impedance. The
amplifier is set up in a gain configuration of +2 to yield an
overall network gain of +1 when driving a double terminated
cable. The value of R3 can be changed if a different network
gain is desired. R5 holds the disable pin at ground thus
inhibiting the amplifier until the switch, S1, is thrown to
position 1. At position 1 the switch pulls the disable pin up to
the plus supply rail thereby enabling the amplifier. Since all
of the actual signal switching takes place within the amplifier,
it’s differential gain and phase parameters, which are 0.03%
and 0.03° respectively, determine the circuit’s performance.
The other circuit, U1B, operates in a similar manner.
When the plus supply rail is 5V the disable pin can be driven
by a dedicated TTL gate as discussed earlier. If a multiplexer
IC or its equivalent is used to select channels its logic must be
break before make. When these conditions are satisfied the
HA-5020 is often used as a remote video multiplexer, and the
multiplexer may be extended by adding more amplifier ICs.
Low Impedance Multiplexer
Two common problems surface when you try to multiplex
multiple high speed signals into a low impedance source
such as an A/D converter. The first problem is the low source
impedance which tends to make amplifiers oscillate and
causes gain errors. The second problem is the multiplexer
which supplies no gain, introduces all kinds of distortion and
limits the frequency response. Using op amps which have an
enable/disable function, such as the HA-5020, eliminates the
multiplexer problems because the external mux chip is not
needed, and the HA-5020 can drive low impedance (large
capacitance) loads if a series isolation resistor is used.
Referring to Figure 9, both inputs are terminated in their
characteristic impedance; 75
Ω is typical for video
applications. Since the drivers usually are terminated in their
characteristic impedance the input gain is 0.5, thus the
amplifiers, U2, are configured in a gain of +2 to set the circuit
gain equal to one. Resistors R2 and R3 determine the
amplifier gain, and if a different gain is desired R2 should be
changed according to the equation G = (1 + R3/R2). R3 sets
the frequency response of the amplifier so you should refer
to the manufacturers data sheet before changing its value.
R5, C1 and D1 are an asymmetrical charge/discharge time
circuit which configures U1 as a break before make switch to
prevent both amplifiers from being active simultaneously. If
this design is extended to more channels the drive logic
must be designed to be break before make. R4 is enclosed
in the feedback loop of the amplifier so that the large open
loop amplifier gain of U2 will present the load with a small
closed loop output impedance while keeping the amplifier
stable for all values of load capacitance.
The circuit shown in Figure 9 was tested for the full range of
capacitor values with no oscillations being observed; thus,
problem one has been solved. The frequency and gain
characteristics of the circuit are now those of the amplifier
and independent of any multiplexing action; thus, problem
two has been solved. The multiplexer transition time is
approximately 15
μs with the component values shown.
NOTES:
24. U1 is HA-5020.
25. All resistors in
Ω.
26. S1 is break before make.
27. Use ground plane.
VIDEO INPUT #1
VIDEO INPUT #2
R1
75
R3
681
R2
681
R4
75
R5
2000
+
-
U1A
U1B
R9
75
R10
2000
R7
681
R8
681
R6
75
+5V IN
+5V
0.1
μF
10
μF
-5V IN
-5V
0.1
μF
10
μF
+
1
R11
100
VIDEO OUTPUT
TO 75
Ω LOAD
+5V
S1
2
3
ALL
OFF
FIGURE 8. TWO CHANNEL HIGH IMPEDANCE MULTIPLEXER
HA-5020
相关PDF资料 |
PDF描述 |
|---|---|
| HFA1105IBZ | IC OPAMP CFA 330MHZ LP 8-SOIC |
| VI-B1N-MU | CONVERTER MOD DC/DC 18.5V 200W |
| HA9P5020-5Z | IC AMP VIDEO 100MHZ CFB 8-SOIC |
| AD7226KN | IC DAC 8BIT LC2MOS QUAD 20-DIP |
| ISL59446IRZ-T7 | IC AMP MUX 4:1 500MHZ 32-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HA3-5020-9 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Current-Feedback Operational Amplifier |
| HA3-5020R2548 | 制造商:Harris Corporation 功能描述: |
| HA350335 | 制造商:HAR 功能描述:350335 HAR'94 S10L2B 制造商:HARRIS 功能描述:IC S11L1C |
| HA3-5033-5 | 功能描述:IC VIDEO BUFFER 250MHZ 8-PDIP RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| HA350D | 制造商:Aleph America Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。