- 您现在的位置：买卖IC网 > PDF目录371784 > HCS473PROM (Microchip Technology Inc.) IC EEPROM SPI BUS 32KBIT 8-SOIC PDF资料下载
参数资料
| 型号： | HCS473PROM |
| 厂商： | Microchip Technology Inc. |
| 英文描述： | IC EEPROM SPI BUS 32KBIT 8-SOIC |
| 中文描述： | 跳码编码器和转发器 |
| 文件页数： | 32/68页 |
| 文件大小： | 1629K |
| 代理商： | HCS473PROM |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
HCS473
DS40035C-page 30
Preliminary
2002 Microchip Technology Inc.
3.2.3.7
ANTI-COLLISION OFF
Anticollision is enabled/disabled for a given device by
the ACOL configuration option. The ANTICOLLISION
OFF command may be used to temporarily bypass
anticollision requirements for a single communication
sequence. It allows communication to an anticollision
enabled HCS473 if the VID and TID are not known
(perhaps during a learning sequence).
The command must immediately follow the wake-up
sequence, Figure 3-18. The HCS473 acknowledges
the command receipt, then reacts to all commands
even if the anticollision (ACOL) configuration option is
enabled and a SELECT TRANSPONDER sequence
has not been performed.
The next command must begin T
CMD
after the
Acknowledge.
The HCS473 remains in this anticollision off state until
the next time the device returns to SLEEP - communi-
cation error or T
CMD
without receiving another com-
mand. Multiple commands may therefore be sent
without sending the ANTICOLLISION OFF command
prior to each command.
FIGURE 3-18:
ANTICOLLISION OFF SEQUENCE (RF RESPONSE EXAMPLE)
3.2.4
LF RESPONSE CONSIDERATIONS
As LF responses are transmitted by the HCS473 plac-
ing a short across the LC antenna inputs, dissipating
the antenna resonance, the transponder reader must
still be sending the 125 kHz field for LF responses to
work. The low frequency field on-time (T
FINH
) must
therefore be approriately adjusted to receive an LF
Acknowledge sequence or LF data response, Figure 3-
19 and Figure 3-20.
3.2.5
CONSECUTIVE COMMAND
CONSIDERATIONS
Transponder commands may consecutively follow one
another to minimize communication time as the wake-
up sequence, device selection, anticollision off and
transport code presentation need not be repeated for
every command.
Consideration must be given to how long the transpon-
der reader keeps the LF signal on after the last data
bit’s rising edge (T
FINH
) when a command sequence...
will be followed by another command sequence
will result in a LF response
The reason is that the HCS473’s analog LF antenna
input circuitry will return to Low-power mode when the
125 kHz field remains absent; requiring a new wake-up
sequence to continue communication.
The HCS473’s analog section will never return to Low-
power mode during any T
CMD
window waiting for an LC
input communication edge, so long as the LF signal
existed up to the beginning of the T
CMD
window.
Please refer to Figure 3-19 and Figure 3-20 for exam-
ples on adjusting T
FINH
for consecutive commands and
LF responses.
3.2.6
LF COMMUNICATION ANALOG
DELAYS
LF communication edge delays result from the
HCS473’s internal analog circuit as well as the external
LC resonant antennas, Figure 3-21.
The rising and falling edge delays inherent to the
HCS473’s internal filtering are known and specified in
Table 7-5, T
FILTR
and
T
FILTF
.
The cumulative rising and falling edge delays inherent
to both the series LC transmitting antenna and parallel
LC receiving antennas are design dependent, not a
HCS473 specification.
CMD
CRC
T
CMD
‘111
2
’
2 bits
T
CMD
‘
‘
‘
L
Command
M
C
C
CRC
ACK
T
FINH
ACOL Off ACK
T
AOACK
WAKE ACK
CMD
‘XXX’
b
b
b
Next
Command
T
CMD
Inductive In
(LC Pins)
T
SF
ACK
RF Response
(DATA Pin)
T
CMD
T
CMD
5 LF
TE
T
CMD
Next
Command
M
L
相关PDF资料 |
PDF描述 |
|---|---|
| HCS473PSQTP | Code Hopping Encoder and Transponder |
| HCS473SLQTP | Code Hopping Encoder and Transponder |
| HCS473SLROM | Code Hopping Encoder and Transponder |
| HCS473SLSQTP | Code Hopping Encoder and Transponder |
| HCS509 | KEELOQ Code Hopping Encoder Product Brief*(KeeLoq 译码器，是NTQ109和NTQ106的替代品) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HCS473-PROM | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder |
| HCS473PSQTP | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder |
| HCS473-PSQTP | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder |
| HCS473SLQTP | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder |
| HCS473-SLQTP | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder |
发布紧急采购，3分钟左右您将得到回复。