- 您现在的位置：买卖IC网 > PDF目录228557 > HEDM-5600 Quick Assembly Two and Three Channel Optical Encoders PDF资料下载
参数资料
| 型号： | HEDM-5600 |
| 英文描述： | Quick Assembly Two and Three Channel Optical Encoders |
| 中文描述： | 快速大会二及中三通道光学编码器 |
| 文件页数： | 2/15页 |
| 文件大小： | 291K |
| 代理商： | HEDM-5600 |
10
3a. Push the hex wrench into the body of the encoder to
ensure that it is properly seated into the code wheel hub set
screws. Then apply a downward force on the end of the hex
wrench. This sets the code wheel gap by levering the code
wheel hub to its upper position.
3b. While continuing to apply a downward force, rotate the
hex wrench in the clockwise direction until the hub set
screw is tight against the motor shaft. The hub set screw
attaches the code wheel to the motor's shaft.
3c. Remove the hex wrench by pulling it straight out of the
encoder body.
4. Use the center screwdriver slot, or either of the two side
slots, to rotate the encoder cap dot clockwise from the one
dot position to the two dot position. Do not rotate the
encoder cap counterclockwise beyond the one dot position.
The encoder is ready for use!
Encoder Mounting and Assembly
1. For HEDS-5500 and 5600: Mount encoder base plate onto
motor. Tighten screws. Go on to step 2.
1a. For HEDS-5540, 5640 and HEDM-5500, 5600: Slip
alignment tool onto motor shaft. With alignment tool in
place, mount encoder baseplate onto motor as shown above.
Tighten screws. Remove alignment tool.
2. Snap encoder body onto base plate locking all 4 snaps.
相关PDF资料 |
PDF描述 |
|---|---|
| HEDM-5600-B01 | Quick Assembly Two and Three Channel Optical Encoders |
| HEDM-5600-B02 | Quick Assembly Two and Three Channel Optical Encoders |
| HEDM-5600-B03 | Quick Assembly Two and Three Channel Optical Encoders |
| HEDM-5600-B04 | Quick Assembly Two and Three Channel Optical Encoders |
| HEDM-5600-B05 | Quick Assembly Two and Three Channel Optical Encoders |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HEDM-5600#B06 | 功能描述:编码器 2 Channel 1000 CPR 1/4in Film CW RoHS:否 制造商:Avago Technologies 产品:Optical Encoders 类型:Absolute 每转脉冲: 制动器数量: 通道数量:2 安装风格:Through Hole 端接类型:Solder Pin 输出: 轴类型: 带开关: 电源电压:5 V 工作温度范围:- 40 C to + 115 C |
| HEDM-5600#B12_W1202-495249 | 制造商:Avago Technologies 功能描述: |
| HEDM-5600#B13 | 功能描述:编码器 2 Channel 1000 CPR 8mm Film CW RoHS:否 制造商:Avago Technologies 产品:Optical Encoders 类型:Absolute 每转脉冲: 制动器数量: 通道数量:2 安装风格:Through Hole 端接类型:Solder Pin 输出: 轴类型: 带开关: 电源电压:5 V 工作温度范围:- 40 C to + 115 C |
| HEDM-5600#J06 | 功能描述:编码器 2 Channel 1024 CPR 1/4in Film CW RoHS:否 制造商:Avago Technologies 产品:Optical Encoders 类型:Absolute 每转脉冲: 制动器数量: 通道数量:2 安装风格:Through Hole 端接类型:Solder Pin 输出: 轴类型: 带开关: 电源电压:5 V 工作温度范围:- 40 C to + 115 C |
| HEDM-5600-B01 | 制造商:HP 制造商全称:Agilent(Hewlett-Packard) 功能描述:Quick Assembly Two and Three Channel Optical Encoders |
发布紧急采购，3分钟左右您将得到回复。