参数资料
| 型号： | HFA1145IBZ |
| 厂商： | Intersil |
| 文件页数： | 9/13页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP CFA 330MHZ LP 8-SOIC |
| 标准包装： | 98 |
| 应用： | 电流反馈 |
| 电路数： | 1 |
| -3db带宽： | 330MHz |
| 转换速率： | 2100 V/µs |
| 电流 - 电源： | 5.8mA |
| 电流 - 输出 / 通道： | 60mA |
| 电压 - 电源，单路/双路(±)： | 9 V ~ 11 V，±4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
| 产品目录页面： | 1234 (CN2011-ZH PDF) |
5
FN3955.5
June 1, 2006
Application Information
Optimum Feedback Resistor
Although a current feedback amplifier’s bandwidth
dependency on closed loop gain isn’t as severe as that of a
voltage feedback amplifier, there can be an appreciable
decrease in bandwidth at higher gains. This decrease may be
minimized by taking advantage of the current feedback
amplifier’s unique relationship between bandwidth and RF. All
current feedback amplifiers require a feedback resistor, even
for unity gain applications, and RF, in conjunction with the
internal compensation capacitor, sets the dominant pole of the
frequency response. Thus, the amplifier’s bandwidth is
inversely proportional to RF. The HFA1145 design is optimized
for RF = 510Ω at a gain of +2. Decreasing RF decreases
stability, resulting in excessive peaking and overshoot (Note:
Capacitive feedback will cause the same problems due to the
feedback impedance decrease at higher frequencies). At
higher gains, however, the amplifier is more stable so RF can
be decreased in a trade-off of stability for bandwidth.
The table below lists recommended RF values for various
gains, and the expected bandwidth. For a gain of +1, a
resistor (+RS) in series with +IN is required to reduce gain
peaking and increase stability.
Non-inverting Input Source Impedance
For best operation, the DC source impedance seen by the
non-inverting input should be
≥50Ω. This is especially
important in inverting gain configurations where the non-
inverting input would normally be connected directly to GND.
DISABLE Input TTL Compatibility
The HFA1145 derives an internal GND reference for the
digital circuitry as long as the power supplies are
symmetrical about GND. With symmetrical supplies the
digital switching threshold (VTH = (VIH + VIL)/2 = (2.0 +
0.8)/2) is 1.4V, which ensures the TTL compatibility of the
DISABLE input. If asymmetrical supplies (e.g. +10V, 0V) are
utilized, the switching threshold becomes:
and the VIH and VIL levels will be VTH ± 0.6V, respectively.
DISABLE Input Logic High Current
VDISABLE = 5V
A
Full
-
1
15
μA
Output Disable Time (Note 6)
VIN = ±1V,
VDISABLE = 2.4V to 0V
B25
-
35
-
ns
Output Enable Time (Note 6)
VIN = ±1V,
VDISABLE = 0V to 2.4V
B
25
-
180
-
ns
Disabled Output Capacitance
VDISABLE = 0V
B
25
-
2.5
-
pF
Disabled Output Leakage
VDISABLE = 0V, VIN = 2V,
VOUT = ±3V
AFull
-
3
10
μA
Off Isolation
(VDISABLE = 0V, VIN = 1VP-P, Note 6)
At 5MHz
B
25
-
-75
-
dB
At 25MHz
B
25
-
-60
-
dB
POWER SUPPLY CHARACTERISTICS
Power Supply Range
C
25
±4.5
-
±5.5
V
Power Supply Current (Note 6)
A
25
-
5.8
6.1
mA
A
Full
-
5.9
6.3
mA
NOTES:
3. Test Level: A. Production Tested; B. Typical or Guaranteed Limit Based on Characterization; C. Design Typical for Information Only.
4. Undershoot dominates for output signal swings below GND (e.g. 0.5VP-P), yielding a higher overshoot limit compared to the VOUT = 0 to 0.5V
condition. See the “Application Information” section for details.
5. Slew rates are asymmetrical if the output swings below GND (e.g. a bipolar signal). Positive unipolar output signals have symmetric positive and
negative slew rates comparable to the +SR specification. See the “Application Information” section, and the pulse response graphs for details.
6. See Typical Performance Curves for more information.
Electrical Specifications
VSUPPLY = ±5V, AV = +1, RF = 510Ω, RL = 100Ω, Unless Otherwise Specified (Continued)
PARAMETER
TEST CONDITIONS
(NOTE 3)
TEST
LEVEL
TEMP. (°C)
MIN
TYP
MAX
UNITS
±
GAIN
(ACL)
RF (Ω)
BANDWIDTH
(MHz)
-1
425
300
+1
510 (+RS = 510Ω)
270
+2
510
330
+5
200
300
+10
180
130
V
TH
V+
V-
+
2
-------------------
1.4V
+
=
HFA1145
相关PDF资料 |
PDF描述 |
|---|---|
| ISL59448IAZ | IC AMP TRIPLE MUX 500MHZ 24-QSOP |
| EL4543ILZ | IC DRIVER TWISTED 350MHZ 20QFN |
| AD669AR | IC DAC 16BIT MONO W/VREF 28-SOIC |
| ISL59440IAZ | IC AMP MULTIPLEX 400MHZ 16-QSOP |
| ISL59420IUZ-T7 | IC AMP MULTIPLEX 400MHZ 10-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HFA1145IP | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| HFA1145IPZ | 功能描述:视频放大器 W/ANNEAL OPAMP 330MHZ CFB DISABLE RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| HFA1145MJ/883 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High Speed, Low Power, Current Feedback Video Operational Amplifier with Output Disable |
| HFA1149 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:450MHz, Low Power, Video Operational Amplifier with Programmable Output Disable |
| HFA1149_04 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:450MHz, Low Power, Video Operational Amplifier with Programmable Output Disable |
发布紧急采购，3分钟左右您将得到回复。