参数资料
| 型号： | HI5760IAZ-T |
| 厂商： | Intersil |
| 文件页数： | 6/18页 |
| 文件大小： | 0K |
| 描述： | CONV D/A 10BIT 125MSPS 28-TSSOP |
| 标准包装： | 1 |
| 设置时间： | 35ns |
| 位数： | 10 |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 电压电源： | 模拟和数字 |
| 功率耗散（最大）： | 165mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 标准包装 |
| 输出数目和类型： | 2 电流，单极 |
| 采样率（每秒）： | 125M |
| 产品目录页面： | 1236 (CN2011-ZH PDF) |
| 其它名称： | HI5760IAZ-TDKR |
14
Definition of Specifications
Integral Linearity Error, INL, is the measure of the worst
case point that deviates from a best fit straight line of data
values along the transfer curve.
Differential Linearity Error, DNL, is the measure of the
step size output deviation from code to code. Ideally the step
size should be 1 LSB. A DNL specification of 1 LSB or less
guarantees monotonicity.
Output Settling Time, is the time required for the output
voltage to settle to within a specified error band measured
from the beginning of the output transition. In the case of the
HI5760, the measurement was done by switching from code
0 to 256, or quarter scale. Termination impedance was 25
due to the parallel resistance of the output 50 and the
oscilloscope’s 50 input. This also aids the ability to resolve
the specified error band without overdriving the oscilloscope.
Singlet Glitch Area, is the switching transient appearing on
the output during a code transition. It is measured as the
area under the overshoot portion of the curve and is
expressed as a Volt-Time specification.
Full Scale Gain Error, is the error from an ideal ratio of 32
between the output current and the full scale adjust current
(through RSET).
Full Scale Gain Drift, is measured by setting the data inputs
to all ones and measuring the output voltage through a
known resistance as the temperature is varied from TMIN to
TMAX. It is defined as the maximum deviation from the value
measured at room temperature to the value measured at
either TMIN or TMAX. The units are ppm of FSR (full scale
range) per degree C.
Total Harmonic Distortion, THD, is the ratio of the DAC
output fundamental to the RMS sum of the first five
harmonics.
Spurious Free Dynamic Range, SFDR, is the amplitude
difference from the fundamental to the largest harmonically or
non-harmonically related spur within the specified window.
Output Voltage Compliance Range, is the voltage limit
imposed on the output. The output impedance load should
be chosen such that the voltage developed does not violate
the compliance range.
Offset Error, is measured by setting the data inputs to all
zeros and measuring the output voltage through a known
resistance. Offset error is defined as the maximum deviation
of the output current from a value of 0mA.
Offset Drift, is measured by setting the data inputs to all
zeros and measuring the output voltage through a known
resistance as the temperature is varied from TMIN to TMAX.
It is defined as the maximum deviation from the value
measured at room temperature to the value measured at
either TMIN or TMAX. The units are ppm of FSR (full scale
range) per degree C.
Power Supply Rejection, is measured using a single power
supply. Its nominal +5V is varied ±10% and the change in
the DAC full scale output is noted.
Reference Input Multiplying Bandwidth, is defined as the
3dB bandwidth of the voltage reference input. It is measured
by using a sinusoidal waveform as the external reference
with the digital inputs set to all 1s. The frequency is
increased until the amplitude of the output waveform is
0.707 of its original value.
Internal Reference Voltage Drift, is defined as the
maximum deviation from the value measured at room
temperature to the value measured at either Tmin or Tmax.
The units are ppm per degree C.
Detailed Description
The HI5760 is a 10-bit, current out, CMOS, digital to analog
converter. Its maximum update rate is 125MSPS and can be
powered by either single or dual power supplies in the
recommended range of +3V to +5V. It consumes less than
165mW of power when using a +5V supply with the data
switching at 100MSPS. The architecture is based on a
segmented current source arrangement that reduces glitch
by reducing the amount of current switching at any one time.
The five MSBs are represented by 31 major current sources
of equivalent current. The five LSBs are comprised of binary
weighted current sources. Consider an input waveform to
the converter which is ramped through all the codes from 0
to 1023. The five LSB current sources would begin to count
up. When they reached the all high state (decimal value of
31) and needed to count to the next code, they would all turn
off and the first major current source would turn on. To
continue counting upward, the 5 LSBs would count up
another 31 codes, and then the next major current source
would turn on and the five LSBs would all turn off. The
process of the single, equivalent, major current source
turning on and the five LSBs turning off each time the
converter reaches another 31 codes greatly reduces the
glitch at any one switching point. In previous architectures
that contained all binary weighted current sources or a
binary weighted resistor ladder, the converter might have a
substantially larger amount of current turning on and off at
certain, worst-case transition points such as mid-scale and
quarter scale transitions. By greatly reducing the amount of
current switching at certain ‘major’ transitions, the overall
glitch of the converter is dramatically reduced, improving
settling times and transient problems.
HI5760
相关PDF资料 |
PDF描述 |
|---|---|
| VI-20F-MY-F4 | CONVERTER MOD DC/DC 72V 50W |
| VI-20F-MY-F3 | CONVERTER MOD DC/DC 72V 50W |
| VE-B1V-MV-F1 | CONVERTER MOD DC/DC 5.8V 75W |
| VI-20F-MY-F1 | CONVERTER MOD DC/DC 72V 50W |
| VI-B1V-MV-F4 | CONVERTER MOD DC/DC 5.8V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HI5762 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 10-Bit, 60MSPS A/D Converter with Internal Voltage Reference |
| HI5762/4IN | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Converter IC |
| HI5762/6IN | 功能描述:CONV A/DDUAL 10BIT 60MSPS 44MQFP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:12 采样率（每秒）:3M 数据接口:- 转换器数目:- 功率耗散（最大）:- 电压电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-23-6 包装:带卷 (TR) 输入数目和类型:- |
| HI5762/6INZ | 功能描述:模数转换器 - ADC W/ANNEAL 44L MQFP IN A/D 10B 60MSPS VREF RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| HI5762_10 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual 10-Bit, 60MSPS A/D Converter with Internal Voltage Reference |
发布紧急采购，3分钟左右您将得到回复。