- 您现在的位置：买卖IC网 > Datasheet目录983 > HI5767EVAL2 (Intersil)EVALUATION PLATFORM HI5767 Datasheet资料下载
参数资料
| 型号： | HI5767EVAL2 |
| 厂商： | Intersil |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | EVALUATION PLATFORM HI5767 |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 10 |
| 采样率（每秒）： | 60M |
| 数据接口： | 并联 |
| 输入范围： | 1 Vpp |
| 在以下条件下的电源（标准）： | 310mW @ 60MSPS |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | HI5767 |
| 已供物品： | 板 |
Application Note 9762
Appendix D HI5767 Theory of Operation
The HI5767 is a 10-bit fully differential sampling pipeline A/D
converter with digital error correction logic. Figure 10 depicts
the circuit for the front end differential-in-differential-out
sample-and-hold (S/H). The switches are controlled by an
internal sampling clock which is a non-overlapping two phase
signal , φ 1 and φ 2 , derived from the master sampling clock.
During the sampling phase, φ 1 , the input signal is applied to
the sampling capacitors, C S . At the same time the holding
capacitors, C H , are discharged to analog ground. At the falling
edge of φ 1 the input signal is sampled on the bottom plates of
the sampling capacitors. In the next clock phase, φ 2 , the two
bottom plates of the sampling capacitors are connected
together and the holding capacitors are switched to the op
amp output nodes. The charge then redistributes between C S
and C H completing one sample-and-hold cycle. The front end
sample-and-hold output is a fully-differential, sampled-data
representation of the analog input. The circuit not only
performs the sample-and-hold function but will also convert a
single-ended input to a fully-differential output for the
converter core. During the sampling phase, the V IN pins see
only the on-resistance of a switch and C S . The relatively small
values of these components result in a typical full power input
bandwidth of 250MHz for the converter.
As illustrated in the functional block diagram, eight identical
pipeline subconverter stages, each containing a two-bit ?ash
converter and a two-bit multiplying digital-to-analog
converter, follow the S/H circuit with the ninth stage being a
two bit ?ash converter. Each converter stage in the pipeline
will be sampling in one phase and amplifying in the other
clock phase. Each individual subconverter clock signal is
offset by 180 degrees from the previous stage clock signal
resulting in alternate stages in the pipeline performing the
same operation.
The output of each of the eight identical two-bit subconverter
stages is a two-bit digital word containing a supplementary bit
to be used by the digital error correction logic. The output of
each subconverter stage is input to a digital delay line which is
controlled by the internal sampling clock. The function of the
digital delay line is to time align the digital outputs of the eight
identical two-bit subconverter stages with the corresponding
output of the ninth stage flash converter before applying the
eighteen bit result to the digital error correction logic. The
buffered latching technique. The digital output data is
available in two’s complement or offset binary format
depending on the state of the Data Format Select (DFS)
control input.
Internal Reference Voltage Output, V REFOUT
The HI5767 is equipped with an internal reference voltage
generator, therefore, no external reference voltage is
required. V REFOUT must be connected to V REFIN when
using the internal reference voltage.
An internal band-gap reference voltage followed by an
amplifier/buffer generates the precision +2.5V reference
voltage used by the converter. A 4:1 array of substrate
PNPs generates the “delta-V BE ” and a two-stage op amp
closes the loop to create an internal +1.25V band-gap
reference voltage. This voltage is then amplified by a wide-
band uncompensated operational amplifier connected in a
gain-of-two configuration. An external, user-supplied,
0.1 μ F capacitor connected from the V REFOUT output pin to
analog ground is used to set the dominant pole and to
maintain the stability of the operational amplifier.
Reference Voltage Input, V REFIN
The HI5767 is designed to accept a +2.5V reference
voltage source at the V REF IN input pin. Typical operation of
the converter requires V REFIN to be set at +2.5V. The
HI5767 is tested with V REFIN connected to V REFOUT
yielding a fully differential analog input voltage range of
± 0.5V.
The user does have the option of supplying an external
+2.5V reference voltage. As a result of the high input
impedance presented at the V REFIN input pin, 2.5k ?
typically, the external reference voltage being used is only
required to source 1mA of reference input current. In the
situation where an external reference voltage will be used
an external 0.1 μ F capacitor must be connected from the
V REFOUT output pin to analog ground in order to maintain
the stability of the internal operational amplifier.
In order to minimize overall converter noise it is
recommended that adequate high frequency decoupling be
provided at the reference voltage input pin, V REFIN .
digital error correction logic uses the supplementary bits to
correct any error that may exist before generating the final ten
bit digital data output of the converter.
Because of the pipeline nature of this converter, the digital
data representing an analog input sample is output to the
digital data bus on the 7th cycle of the clock after the analog
sample is taken. This time delay is speci?ed as the data
V IN +
V IN -
φ 1
φ 2
φ 1
C S
C S
φ 1
φ 1
-
+
C H
C H
φ 1
φ 1
V OUT +
V OUT -
latency. After the data latency time, the digital data
representing each succeeding analog sample is output
during the following clock cycle. The digital output data is
synchronized to the external sampling clock by a double
3-14
FIGURE 10. ANALOG INPUT SAMPLE-AND-HOLD
相关PDF资料 |
PDF描述 |
|---|---|
| HI5805EVAL1 | EVALUATION PLATFORM HI5805 |
| HI5828EVAL2 | EVALUATION PLATFORM HI5828 |
| HI5960SOICEVAL1 | EVALUATION PLATFORM SOIC HI5960 |
| HI7188EVAL | EVALUATION PLATFORM HI7188 |
| HI7190EVAL | EVALUATION PLATFORM HI7190 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HI5780 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:10-Bit, 80 MSPS, High Speed, Low Power D/A Converter |
| HI5780-EV | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:10-Bit, 80 MSPS, High Speed, Low Power D/A Converter |
| HI5780JCQ | 制造商:Rochester Electronics LLC 功能描述:32 PQFP COMTEMP VIDEO D/A 10BIT 80MHZ - Bulk 制造商:Harris Corporation 功能描述: |
| HI5780JCQ-T | 制造商:Rochester Electronics LLC 功能描述:HI5780JCQ IN TAPE & REEL - Bulk |
| HI5800 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:12-Bit, 3MSPS, Sampling A/D Converter |
发布紧急采购，3分钟左右您将得到回复。