- 您现在的位置：买卖IC网 > Datasheet目录983 > HI5805EVAL1 (Intersil)EVALUATION PLATFORM HI5805 Datasheet资料下载
参数资料
| 型号： | HI5805EVAL1 |
| 厂商： | Intersil |
| 文件页数： | 2/15页 |
| 文件大小： | 0K |
| 描述： | EVALUATION PLATFORM HI5805 |
| 标准包装： | 1 |
| ADC 的数量： | 1 |
| 位数： | 12 |
| 采样率（每秒）： | 5M |
| 数据接口： | 并联 |
| 输入范围： | 4 Vpp |
| 在以下条件下的电源（标准）： | 300mW @ 5MSPS |
| 工作温度： | -40°C ~ 85°C |
| 已用 IC / 零件： | HI5805 |
| 已供物品： | 板 |
Application Note 9707
HI5805 A/D Theory of Operation
The HI5805 is a 12-bit fully differential sampling pipelined
A/D converter with digital error correction. Figure 1 depicts
the circuit for the converters front-end differential-in-
differential-out sample-and-hold (S/H). The sampling
switches are controlled by internal sampling clock signals
which consist of two phase non-overlapping clock signals, φ 1
and φ 2, derived from the master clock (CLK) driving the
converter. During the sampling phase, φ 1, the input signal is
applied to the sampling capacitors, C S . At the same time the
holding capacitors, C H , are discharged to analog ground. At
the falling edge of φ 1 the input analog signal is sampled on
the bottom plates of the sampling capacitors. In the next
clock phase, φ 2, the two bottom plates of the sampling
the result that alternate stages in the pipeline will perform the
same operation. The output of each of the three identical four-
bit subconverter stages is a four-bit digital word containing a
supplementary bit to be used by the digital error correction
logic. The output of each subconverter stage is input to a digital
delay line which is controlled by the internal clock. The function
of the digital delay line is to time align the digital outputs of the
three identical four-bit subconverter stages with the
corresponding output of the fourth stage flash converter before
inputting the sixteen bit result into the digital error correction
logic. The digital error correction logic uses the supplementary
bits to correct any error that may exist before generating the
final twelve-bit digital data output (D0-D11) of the converter.
capacitors are connected together and the holding capacitors
are switched to the op amp output nodes. The charge then
redistributes between C S and C H , completing one sample-
and-hold cycle. The output of the sample-and-hold is a fully-
differential, sampled-data representation of the analog input.
The circuit not only performs the sample-and-hold function,
but can also convert a single-ended input to a fully-differential
output for the converter core. During the sampling phase, the
V IN +
V IN -
φ 1
φ 2
φ 1
C S
C S
φ 1
φ 1
C H
- +
+ -
C H
φ 1
φ 1
V OUT +
V OUT -
V IN pins see only the on-resistance of the switches and C S .
The relatively small values of these components result in a
typical full power input bandwidth of 100MHz for the converter.
As illustrated in the HI5805 Functional Block Diagram and the
timing diagram contained Figure 2, three identical pipeline
subconverter stages, each containing a four-bit flash converter,
a four-bit digital-to-analog converter and an amplifier with a
voltage gain of 8, follow the S/H circuit with the fourth stage
being only a 4-bit flash converter. Each converter stage in the
pipeline will be sampling in one phase and amplifying in the
other clock phase. Each individual sub-converter clock signal is
offset by 180 degrees from the previous stage clock signal, with
ANALOG
INPUT
FIGURE 1. ANALOG INPUT SAMPLE-AND-HOLD
Because of the pipeline nature of this converter, the digital
data representing an analog input sample is presented on
the digital data output bus on the 3rd cycle of the clock after
the analog sample is taken. This delay is speci?ed as the
data latency. After the data latency time, the data
representing each succeeding analog sample is output on
the following clock pulse. The output data is synchronized to
the external sampling clock with a data latch and is
presented in offset binary format.
CLOCK
INPUT
S N-1
H N-1
S N
H N
S N+1
H N+1
S N+2
H N+2
S N+3
H N+3
S N+4
H N+4
S N+5
H N+5
S N+6
H N+6
INPUT
S/H
1ST
STAGE
2ND
STAGE
3RD
STAGE
4TH
STAGE
DATA
OUTPUT
B 2, N-2
B 4, N-3
B 1, N-1
B 3, N-2
D N-3
B 2, N-1
B 4, N-2
B 1, N
B 3, N-1
D N-2
B 2, N
B 4, N-1
B 1, N+1
B 3, N
D N-1
B 2, N+1
B 4, N
B 1, N+1
B 3, N+1
D N
B 2, N+1
B 4, N+1
B 1, N+2
B 3, N+1
D N+1
B 2, N+2
B 4, N+1
B 1, N+3
B 3, N+2
D N+1
B 2, N+3
B 4, N+2
B 1, N+7
B 3, N+3
D N+2
NOTES:
t LAT
1. S N : N-th sampling period.
2. H N : N-th holding period.
3. B M , N : M-th stage digital output corresponding to N-th sampled input.
4. D N : Final data output corresponding to N-th sampled input.
FIGURE 2. HI5805 INTERNAL CIRCUIT TIMING
3-2
相关PDF资料 |
PDF描述 |
|---|---|
| HI5828EVAL2 | EVALUATION PLATFORM HI5828 |
| HI5960SOICEVAL1 | EVALUATION PLATFORM SOIC HI5960 |
| HI7188EVAL | EVALUATION PLATFORM HI7188 |
| HI7190EVAL | EVALUATION PLATFORM HI7190 |
| HJ4-L-DC12V | RELAY GEN PURPOSE 4PDT 5A 12V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HI5806IB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HI5808 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:12-Bit, 9MSPS A/D Converter |
| HI5808_01 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:12-Bit, 9MSPS A/D Converter |
| HI5808BIB | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:12-Bit, 9MSPS A/D Converter |
| HI5808BIBR4499 | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Harris Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。