- 您现在的位置：买卖IC网 > PDF目录17050 > HI5860SOICEVAL1 (Intersil)EVALUATION PLATFORM SOIC HI5860 PDF资料下载
参数资料
| 型号： | HI5860SOICEVAL1 |
| 厂商： | Intersil |
| 文件页数： | 2/8页 |
| 文件大小： | 0K |
| 描述： | EVALUATION PLATFORM SOIC HI5860 |
| 标准包装： | 1 |
| 系列： | CommLink™ |
| DAC 的数量： | 1 |
| 位数： | 12 |
| 采样率（每秒）： | 130M |
| 数据接口： | 并联 |
| 设置时间： | 35ns |
| DAC 型： | 电流 |
| 工作温度： | -40°C ~ 85°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | HI5860 |
Application Note 9853
Functional Descriptions
Voltage Reference
The HI5860/5960 has an internal 1.2V voltage reference with
a ± 40ppm/ o C drift coefficient over the industrial temperature
range. The REFLO pin (16) selects the reference. Access to
pin 16 is provided through the center pin of Jumper J3. This
jumper is labeled INT and EXT for internal or external
reference. The REFIO pin (17) provides access to the internal
voltage reference, or can be overdriven if the user wishes to
use an external source for the reference. The internal
Transformer Output
The evaluation board is con?gured with a transformer output
con?guration, shown in Figure 1. This con?guration was
chosen because it provides: even harmonic performance
improvement due to the differential signaling; ~12.5 ? R EQ
loading to each output of the DAC; drive impedance of 50 ?
for matching with a spectrum analyzer; and 2x voltage gain.
The output of this con?guration will be biased at zero volts
and have an amplitude of ~500mV (V OUT ) when the DAC is
con?gured to drive I OUTFS of 20mA.
reference was not designed to drive an external load. Notice
that a 0.1 μ F capacitor is placed as close as possible to the
HI5x60
V OUT = (2 x I OUTFS x R EQ )V
REFIO pin. This capacitor is necessary for ensuring a noise
free reference voltage. If the user wishes to use an external
reference voltage, jumper J1 must be in place and an external
voltage reference provided via SMA1, labeled ‘EXT REF’. The
recommended limits of the external reference are between
PIN 21
PIN 22
IOUTB
IOUTA
50 ?
100 ?
50 ?
50 ?
SPECTRUM
ANALYZER’S
INPUT
IMPEDANCE
15mV and 1.2V. Performance of the converter can be
expected to decline as the reference voltage is reduced due to
the reduction in LSB current size. If the user wishes to
amplitude modulate the DAC, the REFIO pin can be
overdriven with a waveform. The input multiplying bandwidth
of the REFIO input is approximately 1.4MHz when driving a
100mV signal into the REFIO pin, biased at 0.6V DC . The 3dB
BW reduces as this amplitude is increased. It is necessary
that the multiplying signal be DC offset so that the minimum
and maximum peaks are positive and below 1.2V. For the
external reference option, Jumper J3 must be changed so that
pin 16 of the DAC is tied to the supply voltage, which is the
EXT side of J3. The output current of the converter, IOUTA
and IOUTB, is a function of the voltage reference used and
the value of R SET (or R2) on the schematic.
Output Current
The output current of the device is set by choosing R SET
and V FSADJ such that the resultant of the following equation
is less than 20mA:
I OUT = 32 x V FSADJ /R SET.
REFIO (PIN 17) and FSADJ (PIN 18) of the DAC are the
inputs to an operational amplifier. The voltage at the
FSADJ pin (V FSADJ ) will be approximately equal to the
voltage at the REFIO pin, which will either be the value of
the internal or external reference. For example, using the
internal reference of (nominal) 1.2V and an R SET value of
1.91k ? results in an I OUT of approximately 20mA
(maximum allowed). Choose the output loading so that the
Output Voltage Compliance Range is not violated (-0.3 to
1.25V). If an external reference is chosen, it should not
exceed +1.2V.
The output can be con?gured to drive a load resistor, a
transformer, an operational ampli?er, or any other type of
output con?guration so long as the output voltage
compliance range and the maximum output current are not
violated.
3-2
FIGURE 1.
Sleep
The converter can be put into ‘sleep’ mode by connecting pin
15 of the DAC to either of the converter’s supply voltages.
The sleep pin has an active pulldown current, so the pin can
be left disconnected or be grounded for normal (awake)
operation. On the evaluation board, jumper J2 is provided for
controlling the sleep pin. Remove the jumper from J2 for
normal operation and replace it for sleep mode.
Power Supply(s) and Ground(s)
The user can operate from either a single supply or from
dual supplies. The supplies can be at different voltages. It is
important to note that the digital inputs cannot switch more
than 0.3V above the digital supply voltage. The evaluation
board contains two power supply connections, (analog)
AV DD1 and (digital) DV DD1 , each with their own ground wire.
Dual ground and power planes is the recommended
con?guration, with the ground planes connected at a single
point near the DAC.
Digital Inputs
The DAC is designed to accept CMOS inputs. The switching
voltage is approximately 1/2 of the digital power supply
voltage, so reducing the power supply can make the DAC
compatible to smaller levels. The digital inputs (data and
clock) cannot go +0.3V higher than the digital supply
voltage, else diode ESD protection can begin to turn on and
performance could be degraded. The clock source can be a
sine wave, with some degradation in performance. The
recommended clock is a square wave.
The timing between the clock and the data will affect spectral
performance and functionality. Minimum setup and hold
times are speci?ed in the datasheet to represent the point at
which the DAC begins to lose bits. Optimal setup and hold
相关PDF资料 |
PDF描述 |
|---|---|
| REC5-0505DRW/H2/A | CONV DC/DC 5W 4.5-9VIN +/-05VOUT |
| REC5-483.3DRW/H2/C | CONV DC/DC 5W 36-72VIN +/-3.3V |
| GCM22DCMH | CONN EDGECARD 44POS .156 WW |
| ISL5961EVAL1 | ISL5961 -SOICEVALUATION PLATF |
| REC5-483.3DRW/H2/A | CONV DC/DC 5W 36-72VIN +/-3.3V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HI5865 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:12-Bit, 65 MSPS A/D Converter |
| HI5865EVAL1 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:12-Bit, 65 MSPS A/D Converter |
| HI5865IN | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:12-Bit, 65 MSPS A/D Converter |
| HI5905 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:14-Bit, 5MSPS A/D Converter |
| HI5905_03 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:14-Bit, 5MSPS A/D Converter |
发布紧急采购，3分钟左右您将得到回复。