- 您现在的位置：买卖IC网 > PDF目录385381 > HIP1020CK-T (HARRIS SEMICONDUCTOR) nullSingle, Double or Triple-Output Hot Plug Controller PDF资料下载
参数资料
| 型号： | HIP1020CK-T |
| 厂商： | HARRIS SEMICONDUCTOR |
| 元件分类： | 稳压器 |
| 英文描述： | nullSingle, Double or Triple-Output Hot Plug Controller |
| 中文描述： | SWITCHED CAPACITOR CONVERTER, PDSO5 |
| 文件页数： | 2/6页 |
| 文件大小： | 51K |
| 代理商： | HIP1020CK-T |
2-2
Pin Descriptions
PIN
SYMBOL
FUNCTION
DESCRIPTION
1
VCC
Bias Supply
Connect this pin to either a 12V or a 5V source. The HIP1020 detects the bias-voltage level at
pin 1 and decides whether to operate as a voltage-doubler or a voltage-tripler. Consequently,
it is not recommended to operate with bias voltages between 5V (
±
10%) and 12V (
±
10%). In
the absence of an enable signal at pin 5, the current into pin 1 is less than 1
μ
A. It is necessary
for voltage to be present at pin 1 prior to applying an enable signal at pin 5.
2
GND
Ground
Connect to the negative rail of the supply that is connected to pin 1.
3
LGATE
Gate Driver for the 5V
and/or 3.3V
MOSFET(s)
When VCC = 12V, connect this pin to the gate(s) of the 5V and/or 3.3V MOSFETs. When VCC
= 5V, connect this pin to the gate of a 3.3V MOSFET. Upon a rising edge on EN (pin 5), the
voltage on this pin will ramp linearly to ~16V when VCC = 12V and ~12V when VCC = 5V. An
internal dv/dt activated clamp shunts coupled noise to ground preventing unintended turn on at
either output. The internal dv/dt-activated clamp also protects pin 5.
4
HGATE
12V or 5V MOSFET
Gate Driver
When VCC = 12V, connect this pin to the gate of the 12V MOSFET. When VCC = 5V, connect
this pin to the gate of the 5V MOSFET. Upon a rising edge on EN (pin 5), the voltage on this
pin will ramp linearly to ~22V when VCC = 12V and ~13V when VCC = 5V.
5
EN
Enable
Connect a TTL or 3.3V logic signal to this pin to control the outputs at pins 3 and 4. A rising
edge on pin 5 initiates the linear voltage ramps at pins 3 and 4. Be sure that the device driving
EN does not enter a high-impedance state when enabling is not desired and that it’s maximum
rise time does not exceed 100
μ
s.
HIP1020
相关PDF资料 |
PDF描述 |
|---|---|
| HIP2030 | 30V MCT/IGBT Gate Driver(MOS可控硅晶体管/绝缘栅双极晶体管门驱动器) |
| HIP2100IB | 100V/2A Peak, Low Cost, High Frequency Half Bridge Driver |
| HIP5015EVAL2 | () |
| HIP5060DW | Power Control IC Single Chip PowerSupply |
| HIP5060DY | FPGA 1000000 SYSTEM GATE 1.8 VOLT - NOT RECOMMENDED for NEW DESIGN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP1020CKZ-T | 功能描述:热插拔功率分布 DEVICE BAY PWR CNTRLR RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| HIP1030 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:1A High Side Driver with Overload Protection |
| HIP1030_00 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:1A High Side Driver with Overload Protection |
| HIP1030AS | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:1A High Side Driver with Overload Protection |
| HIP1031 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Half Amp High Side Driver with Overload Protection |
发布紧急采购，3分钟左右您将得到回复。