参数资料
型号: HIP6013CB-T
厂商: Intersil
文件页数: 6/11页
文件大小: 0K
描述: IC CONTROLLER PWM BUCK 14-SOIC
标准包装: 2,500
应用: 控制器,Intel Pentium? Pro、PowerP、Alpha
输入电压: 5V,12V
输出数: 1
输出电压: 1.3 V ~ 12 V
工作温度: 0°C ~ 70°C
安装类型: *
封装/外壳: 14-SOIC(0.154",3.90mm 宽)
供应商设备封装: *
包装: 带卷 (TR)
HIP6013
V IN
4V
2V
HIP6013
0V
15A
UGATE
PHASE
Q1
L O
V OUT
10A
D2
C IN
C O
5A
0A
RETURN
TIME (20ms/DIV)
r DS ( ON )
FIGURE 4. OVER-CURRENT OPERATION
The over-current function will trip at a peak inductor current
(I PEAK ) determined by:
I OCSET ? R OCSET
I PEAK = ---------------------------------------------------
where I OCSET is the internal OCSET current source (200 μ A
- typical). The OC trip point varies mainly due to the
MOSFET’s r DS(ON) variations. To avoid over-current tripping
in the normal operating load range, find the R OCSET resistor
from the equation above with:
1. The maximum r DS(ON) at the highest junction temperature.
2. The minimum I OCSET from the specification table.
3. Determine I PEAK for I PEAK > I OUT ( MAX ) + ( ? I ) ? 2 ,
where ? I is the output inductor ripple current.
For an equation for the ripple current see the section under
component guidelines titled ‘Output Inductor Selection’.
A small ceramic capacitor should be placed in parallel with
R OCSET to smooth the voltage across R OCSET in the
presence of switching noise on the input voltage.
FIGURE 5. PRINTED CIRCUIT BOARD
POWER AND GROUND PLANES OR ISLANDS
Figure 5 shows the critical power components of the
converter. To minimize the voltage overshoot the
interconnecting wires indicated by heavy lines should be part
of ground or power plane in a printed circuit board. The
components shown in Figure 6 should be located as close
together as possible. Please note that the capacitors C IN
and C O each represent numerous physical capacitors.
Locate the HIP6013 within 3 inches of the MOSFETs, Q1.
The circuit traces for the MOSFETs’ gate and source
connections from the HIP6013 must be sized to handle up to
1A peak current.
Figure 6 shows the circuit traces that require additional
layout consideration. Use single point and ground plane
construction for the circuits shown. Minimize any leakage
current paths on the SS PIN and locate the capacitor, C ss
close to the SS pin because the internal current source is
only 10 μ A. Provide local V CC decoupling between VCC and
GND pins. Locate the capacitor, C BOOT as close as practical
to the BOOT and PHASE pins.
Application Guidelines
BOOT
D1
+V IN
Layout Considerations
As in any high frequency switching converter, layout is very
important. Switching current from one power device to another
can generate voltage transients across the impedances of the
SS
HIP6013
C BOOT
PHASE
V CC
+12V
Q1 L O
D2 C O
V OUT
interconnecting bond wires and circuit traces. These
interconnecting impedances should be minimized by using
wide, short printed circuit traces. The critical components
should be located as close together as possible using ground
C SS
GND
C VCC
plane construction or single point grounding.
FIGURE 6. PRINTED CIRCUIT BOARD
SMALL SIGNAL LAYOUT GUIDELINES
6
4325.1
November 3, 2005
相关PDF资料
PDF描述
HIP6301CB IC REG CTRLR BUCK PWM 20-SOIC
HIP6302CB IC REG CTRLR BUCK PWM 16-SOIC
HIP6302VCB-T IC REG CTRLR BUCK PWM 16-SOIC
HIP6303CB-T IC REG CTRLR BUCK PWM 20-SOIC
HIP6311ACB-T IC REG CTRLR BUCK PWM 20-SOIC
相关代理商/技术参数
参数描述
HIP6013CBZ 功能描述:电压模式 PWM 控制器 STD BUCK PWM/1 5%/14 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
HIP6013CBZ-T 功能描述:电压模式 PWM 控制器 STD BUCK PWM/1 5%/14 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
HIP6014 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor
HIP6014CB 制造商:Rochester Electronics LLC 功能描述:- Bulk
HIP6014CB WAF 制造商:Harris Corporation 功能描述: