参数资料
| 型号： | HIP6303CB-T |
| 厂商： | Intersil |
| 文件页数： | 9/17页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 20-SOIC |
| 标准包装： | 1,000 |
| PWM 型： | 控制器 |
| 输出数： | 4 |
| 频率 - 最大： | 350kHz |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 包装： | 带卷 (TR) |
HIP6303
explained above. After this period and a short interval
described above, the PWM outputs are initiated and the
voltage rises in 10.08ms, for a total delay time DT of
10.24ms.
Figure 3 shows the start-up sequence as initiated by a fast
rising 5V supply, V CC, applied to the HIP6303. Note the
short rise to the three state level in PWM 1 output during ?rst
Figure 5 shows the regulator operating from an ATX supply.
In this ?gure, note the slight rise in PGOOD as the 5V supply
rises.The PGOOD output stage is made up of NMOS and
PMOS transistors. On the rising V CC , the PMOS device
becomes active slightly before the NMOS transistor pulls
“down”, generating the slight rise in the PGOOD voltage.
.
32 PWM cycles.
12V ATX
SUPPLY
PWM 1
OUTPUT
PGOOD
DELAY TIME
PGOOD
V CORE
5V
V CC
V CORE
5 V ATX
SUPPLY
V IN = 5V, CORE LOAD CURRENT = 31A
FREQUENCY 200kHZ
ATX SUPPLY ACTIVATED BY ATX “PS-ON PIN”
FIGURE 5. SUPPLY POWERED BY ATX SUPPLY
V IN = 12V
FIGURE 3. START-UP OF 4 PHASE SYSTEM OPERATING AT
500kHz
Figure 4 shows the waveforms when the regulator is
operating at 200kHz. Note that the Soft-Start duration is a
function of the Channel Frequency as explained previously.
Also note the pulses on the COMP terminal. These pulses
are the current correction signal feeding into the comparator
input (see the Block Diagram on page 2).
V COMP
DELAY TIME
PGOOD
V CORE
5V
V CC
V IN = 12V
FIGURE 4. START-UP OF 4 PHASE SYSTEM OPERATING AT
200kHz
Note that Figure 5 shows the 12V gate driver voltage
available before the 5V supply to the HIP6303 has reached
its threshold level. If conditions were reversed and the 5V
supply was to rise ?rst, the start-up sequence would be
different. In this case the HIP6303 will sense an over-current
condition due to charging the output capacitors. The supply
will then restart and go through the normal Soft-Start cycle.
Fault Protection
The HIP6303 protects the microprocessor and the entire
power system from damaging stress levels. Within the
HIP6303 both Over-Voltage and Over-Current circuits are
incorporated to protect the load and regulator.
Over-Voltage
The VSEN pin is connected to the microprocessor CORE
voltage. A CORE over-voltage condition is detected when
the VSEN pin goes more than 15% above the programmed
VID level.
The over-voltage condition is latched, disabling normal PWM
operation, and causing PGOOD to go low. The latch can
only be reset by lowering and returning V CC high to initiate a
POR and Soft-Start sequence.
During a latched over-voltage, the PWM outputs will be
driven either low or three state, depending upon the VSEN
input. PWM outputs are driven low when the VSEN pin
detects that the CORE voltage is 15% above the
programmed VID level. This condition drives the PWM
outputs low, resulting in the lower or synchronous recti?er
9
相关PDF资料 |
PDF描述 |
|---|---|
| HIP6311ACB-T | IC REG CTRLR BUCK PWM 20-SOIC |
| HIP6311CB-T | IC REG CTRLR BUCK PWM 20-SOIC |
| HIP6501ACB-T | IC PWM TRIPLE POWER CTRLR 16SOIC |
| HIP6503CBZ | IC ACPI MULTI POWER CTRLR 20SOIC |
| HM-H088FR1-8CP1-TG30L | CONN HEADER HSHM 88POS 8ROW STR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP6303EVAL1 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| HIP6304 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| HIP6304 WAF | 制造商:Intersil Corporation 功能描述: |
| HIP6304CB | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intersil Corporation 功能描述: |
| HIP6304CB-T | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel 制造商:Intersil Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。