参数资料
| 型号： | HIP9011ABT |
| 厂商： | Intersil |
| 文件页数： | 6/11页 |
| 文件大小： | 0K |
| 描述： | IC SENSOR ENGINE KNOCK 20-SOIC |
| 标准包装： | 1,000 |
| 类型： | 引擎敲击信号处理器 |
| 输入类型： | 逻辑 |
| 输出类型： | 逻辑 |
| 接口： | SPI |
| 电流 - 电源： | 8mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC |
| 包装： | 带卷 (TR) |
4
FN4367.2
January 6, 2006
INPUT AMPLIFIERS
CH0 and CH1 High Output Voltage
VOUTHI
ISINK = 100A, VDD = 5.0V
4.7
4.9
-
V
CH0 and CH1 Low Output Voltage
VOUTLO
ISOURCE = 100A; VDD = 5.0V
-
15
200
mV
Voltage Gain
ACL
Input R = 47.5K, Feedback
R = 475k
+18
+20
+21
dB
ANTIALIASING FILTER
Response 1kHz to 20kHz, Referenced to 1kHz
BW
Test Mode
-
-0.5
-
dB
Attenuation at 180kHz, Referenced
to 1kHz
ATTEN
Test Mode
-10
-15
-
dB
PROGRAMMABLE FILTERS
Peak to Peak Voltage Output
VOUT
Run Mode
3.5
4.0
-
VP-P
Filters Q (Note 2)
Q
Run Mode
-
2.5
-
Q
PROGRAMMABLE GAIN AMPLIFIERS
Percent Amplifier Gain Deviation
%G
Run Mode
-
±1-
%
INTEGRATOR
Integrator Reset Voltage
VRESET
Pin 4 Voltage at Start of
Integration
Cycle; VDD = 5.0V
75
125
175
mV
Integrator Droop after 500
sVDROOP
Hold Mode, Pin 7 = 0V,
VDD =5.0V
Pin 4 set to 20% to 80% of VDD
-
±3
±50
mV
DIFFERENTIAL CONVERTER
Differential to Single Ended Converter Offset
Voltage
DIFVIO
By Design
-
0.1
-
mV
Change In Converter Output
DIFOUT
Run Mode, 500
A Sinking Load
to No Load Condition
-
±1
±10
mV
SYSTEM GAIN DEVIATION
Gain Deviation from “Ideal Equation” Correlation
Factor + 5.0% (Note 3)
VOUT -
VRESET
Run Mode, maximum signal
output from Input Amplifier
<2.25VP-P, Equation Output X
0.95 + Device Reset Voltage;
For Total VOUT ≤ 4.7V
-8%,
±100mV
Equatio
n
X 0.95
-
VRESET
8%,
±100mV
V
NOTES:
2. Q = fo/BW, where: fo = Center Frequency, BW = 3dB Bandwidth
3. Ideal Equation: INTOUT (Volts) = [VIN * GIN * GPR * GBPF * 1/π * (N/tC(ms) * fQ(kHz)) * GDSE] + VRESET
Where: VIN = input signal amplitude (VP-P)
GIN = External Input Gain; GIN = RF/RIN
GPR = Programmed Gain
GBPF = Gain of Bandpass Filter (2 for Ideal Case at Center)
tINT = Integration Time; tINT = N/fQ
0.318 = 1/
π
N = Number of Cycles of Input Signal
fQ = Frequency of Input Signal
RF = Feedback Resistor Value
RIN = Signal Input Resistor Value
tC = Programmed Time Constant
GDSE = Gain of DSE Converter (2 for Ideal Case)
VRESET = Integrator Reset Voltage = 0.125V, Typ
Electrical Specifications
VDD = 5V ±5%, GND = 0V, Clock Frequency 4MHz ±0.1%, TA = -40
oC to 125oC,
Unless Otherwise Specified (Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNITS
HIP9011
相关PDF资料 |
PDF描述 |
|---|---|
| HS1-3182-9+ | IC LN-DRVR ARINC 429 16-SBDIP |
| HSP43124SC-45Z | IC I/O FILTER SER 24BIT 28-SOIC |
| HSP43168JC-33Z | IC FIR FILTER DUAL 84-PLCC |
| HSP43216JC-52Z | IC HALFBAND FILTER 84-PLCC |
| HSP43220JC-33Z | IC DECIMATING DGTL FILTER 84PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP9011ABTS2537 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP9011ABTS266 | 制造商:Intersil Corporation 功能描述: |
| HIP9011ABTS2667 | 制造商:Intersil Corporation 功能描述: |
| HIP9011ABTS2668 | 制造商:Intersil Corporation 功能描述: |
| HIP9011ABZ | 功能描述:接口 - 专用 W/ANNEAL KNOCK SENSOR 20 TUBES RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。