- 您现在的位置：买卖IC网 > PDF目录65465 > HMC-MDB277 (HITTITE MICROWAVE CORP) 70000 MHz - 90000 MHz RF/MICROWAVE DOUBLE BALANCED MIXER PDF资料下载
参数资料
| 型号： | HMC-MDB277 |
| 厂商： | HITTITE MICROWAVE CORP |
| 元件分类： | 混频器 |
| 英文描述： | 70000 MHz - 90000 MHz RF/MICROWAVE DOUBLE BALANCED MIXER |
| 封装： | 1.55 X 1.4 MM, 0.1 MM HEIGHT, DIE-3 |
| 文件页数： | 4/4页 |
| 文件大小： | 147K |
| 代理商： | HMC-MDB277 |
M
IX
E
R
S
-
DO
UBL
E
-B
A
L
A
N
C
E
D
-
C
H
IP
4
4 - 99
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC-MDB277
v01.0209
GaAs MMIC FUNDAMENTAL
MIXER, 70 - 90 GHz
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina
thin film substrates are recommended for bringing RF to and from the chip
(Figure 1). If 0.254mm (10 mil) thick alumina thin film substrates must be
used, the die should be raised 0.150mm (6 mils) so that the surface of
the die is coplanar with the surface of the substrate. One way to accom-
plish this is to attach the 0.102mm (4 mil) thick die to a 0.150mm (6 mil)
thick molybdenum heat spreader (moly-tab) which is then attached to the
ground plane (Figure 2).
Microstrip substrates should be placed as close to the die as possible in
order to minimize bond wire length. Typical die-to-substrate spacing is
0.076mm to 0.152 mm (3 to 6 mils).
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protec-
tive containers, and then sealed in an ESD protective bag for shipment.
Once the sealed ESD protective bag has been opened, all die should be
stored in a dry nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt
to clean the chip using liquid cleaning systems.
Static Sensitivity: Follow ESD precautions to protect against ESD
strikes.
Transients: Suppress instrument and bias supply transients while bias is
applied. Use shielded signal and bias cables to minimize inductive pick-
up.
General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The
surface of the chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy.
The mounting surface should be clean and flat.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool
temperature of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO
NOT expose the chip to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of
scrubbing should be required for attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed
around the perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
RF bonds made with 0.003” x 0.0005” ribbon are recommended. These bonds should be thermosonically bonded
with a force of 40-60 grams. DC bonds of 0.001” (0.025 mm) diameter, thermosonically bonded, are recommended.
Ball bonds should be made with a force of 40-50 grams and wedge bonds at 18-22 grams. All bonds should be made
with a nominal stage temperature of 150 °C. A minimum amount of ultrasonic energy should be applied to achieve
reliable bonds. All bonds should be as short as possible, less than 12 mils (0.31 mm).
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
RF Ground Plane
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
0.076mm
(0.003”)
Figure 1.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
RF Ground Plane
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
0.076mm
(0.003”)
Figure 2.
0.150mm (0.005”) Thick
Moly Tab
相关PDF资料 |
PDF描述 |
|---|---|
| HMC-VVD102 | 17000 MHz - 27000 MHz RF/MICROWAVE VARIABLE ATTENUATOR, 2 dB INSERTION LOSS-MAX |
| HMC-VVD106 | 36000 MHz - 50000 MHz RF/MICROWAVE VARIABLE ATTENUATOR, 2 dB INSERTION LOSS-MAX |
| HMC-XDH158 | 14000 MHz - 16000 MHz RF/MICROWAVE FREQUENCY QUADRUPLER, 14 dB CONVERSION LOSS-MAX |
| HMC110 | 0 MHz - 10000 MHz RF/MICROWAVE VARIABLE ATTENUATOR, 7 dB INSERTION LOSS-MAX |
| HMC128 | 1800 MHz - 5000 MHz RF/MICROWAVE DOUBLE BALANCED MIXER, 10 dB CONVERSION LOSS-MAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HMC-MDB277-SX | 功能描述:RF Mixer IC Radar Up/Down Converter 70GHz ~ 90GHz Die 制造商:analog devices inc. 系列:- 包装:散装 零件状态:有效 RF 类型:雷达 频率:70GHz ~ 90GHz 混频器数:1 增益:- 噪声系数:- 辅助属性:升/降频器 电流 - 电源:- 电压 - 电源:- 封装/外壳:模具 供应商器件封装:模具 标准包装:2 |
| HMCP003A0CA02 | 制造商:Eaton Corporation 功能描述:HMCP STANDARD MAG STYLE W/AUX SWITCH |
| HMCP007C0 | 制造商:Eaton Corporation 功能描述:HMCP STANDARD MAG STYLE ALUMINUM COLLARS |
| HMCP007C0C | 制造商:Eaton Corporation 功能描述:CIRCUIT BREAKER THERMAL MAGNE 制造商:Eaton Corporation 功能描述:CIRCUIT BREAKER, THERMAL MAGNETIC, 3P, 7 制造商:Eaton Corporation 功能描述:CIRCUIT BREAKER, THERMAL MAGNETIC, 3P, 7A; Voltage Rating VDC:250V; Voltage Rating VAC:600V; Current Rating:7A; No. of Poles:3; Circuit Breaker Mounting:Panel; Actuator Style:Lever; Series:C ;RoHS Compliant: Yes |
| HMCP007COC03 | 制造商:Eaton Corporation 功能描述:HMCP 3P 7A W/AL SW TERM BLK RH TERM L&L |
发布紧急采购，3分钟左右您将得到回复。