参数资料
| 型号： | ICL3241ECBZ-T |
| 厂商： | Intersil |
| 文件页数： | 10/33页 |
| 文件大小： | 0K |
| 描述： | IC 3DRVR/5RCVR RS232 3V 28-SOIC |
| 标准包装： | 1,000 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 3/5 |
| 规程： | RS232 |
| 电源电压： | 3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
18
FN4910.21
February 22, 2010
Devices with the automatic power-down feature include
an INVALID output signal, which switches low to indicate
that invalid levels have persisted on all of the receiver
inputs for more than 30s (see Figure 7). INVALID
switches high 1s after detecting a valid RS-232 level on
a receiver input. INVALID operates in all modes (forced
or automatic power-down, or forced on), so it is also
useful for systems employing manual power-down
circuitry. When automatic power-down is utilized,
INVALID = 0 indicates that the ICL32xxE is in
power-down mode.
The time to recover from automatic power-down mode is
typically 100s.
Receiver ENABLE Control
(ICL3221E, ICL3222E, ICL3223E, ICL3241E
Only)
Several devices also feature an EN input to control the
receiver outputs. Driving EN high disables all the
inverting (standard) receiver outputs placing them in a
high impedance state. This is useful to eliminate supply
current, due to a receiver output forward biasing the
protection diode, when driving the input of a powered
input has no effect on transmitter nor monitor (ROUTB)
outputs.
Capacitor Selection
The charge pumps require 0.1F capacitors for 3.3V
operation. For other supply voltages refer to Table 3 for
capacitor values. Do not use values smaller than those
listed in Table 3. Increasing the capacitor values (by a
factor of 2) reduces ripple on the transmitter outputs and
slightly reduces power consumption. C2, C3, and C4 can
be increased without increasing C1’s value, however, do
not increase C1 without also increasing C2, C3, and C4 to
maintain the proper ratios (C1 to the other capacitors).
When using minimum required capacitor values, make
sure that capacitor values do not degrade excessively
with temperature. If in doubt, use capacitors with a
larger nominal value. The capacitor’s equivalent series
resistance (ESR) usually rises at low temperatures and it
influences the amount of ripple on V+ and V-.
Power Supply Decoupling
In most circumstances a 0.1F bypass capacitor is
adequate. In applications that are particularly sensitive
to power supply noise, decouple VCC to ground with a
capacitor of the same value as the charge-pump
capacitor C1. Connect the bypass capacitor as close as
possible to the IC.
Operation Down to 2.7V
ICL32xxE transmitter outputs meet RS-562 levels
(±3.7V), at full data rate, with VCC as low as 2.7V.
RS-562 levels typically ensure interoperability with
RS-232 devices.
Transmitter Outputs when
Exiting Power-Down
Figure 8 shows the response of two transmitter outputs
when exiting power-down mode. As they activate, the
two transmitter outputs properly go to opposite RS-232
levels, with no glitching, ringing, nor undesirable
transients. Each transmitter is loaded with 3kΩ in parallel
with 2500pF. Note that the transmitters enable only
when the magnitude of the supplies exceed
approximately 3V..
Mouse Driveability
The ICL3241E and ICL3243E have been specifically
designed to power a serial mouse while operating from
low voltage supplies. Figure 9 shows the transmitter
RECEIVER
INPUTS
TRANSMITTER
OUTPUTS
INVALID
OUTPUT
V+
VCC
0
V-
VCC
0
tINVL
tINVH
INVALID
REGION
}
FIGURE 7. AUTOMATIC POWER-DOWN AND
INVALID TIMING DIAGRAMS
AUTOPWDN
PWR UP
TABLE 3. REQUIRED CAPACITOR VALUES
VCC
(V)
C1
(F)
C2, C3, C4
(F)
3.0 to 3.6
0.1
4.5 to 5.5
0.047
0.33
3.0 to 5.5
0.1
0.47
TIME (20s/DIV)
T1
T2
2V/DIV
5V/DIV
VCC = +3.3V
FORCEOFF
FIGURE 8. TRANSMITTER OUTPUTS WHEN EXITING
POWER-DOWN
C1 - C4 = 0.1F
ICL3221E, ICL3222E, ICL3223E, ICL3232E, ICL3241E, ICL3243E
相关PDF资料 |
PDF描述 |
|---|---|
| V300B36M250BF | CONVERTER MOD DC/DC 36V 250W |
| IDT72815LB15BG | IC FIFO SYNC DUAL 512X18 121BGA |
| MS27467E15A5P | CONN PLUG 5POS STRAIGHT W/PINS |
| IDT72825LB25BG | IC FIFO SYNC DL 1024X18 121BGA |
| ICL3238IAZ-T | IC 5DRVR/3RCVR RS232 3V 28-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICL3241ECV | 功能描述:IC 3DRVR/5RCVR RS232 3V 28-TSSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件 |
| ICL3241ECV-T | 功能描述:IC 3DRVR/5RCVR RS232 3V 28-TSSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件 |
| ICL3241ECVZ | 功能描述:RS-232接口集成电路 RS232 3V 3D/5R 15KV SHTDWN 28TSSOP COM RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| ICL3241ECVZ-T | 功能描述:RS-232接口集成电路 RS232 3V 3D/5R 15KV SHTDWN 28TSSOP COMEL RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| ICL3241EIA | 功能描述:IC 3DRVR/5RCVR RS232 3V 28-SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。