- 您现在的位置：买卖IC网 > PDF目录20100 > ICL7107SCPL (Intersil)IC ADC 3.5 DIGIT LED 40-DIP PDF资料下载
参数资料
| 型号： | ICL7107SCPL |
| 厂商： | Intersil |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | IC ADC 3.5 DIGIT LED 40-DIP |
| 标准包装： | 9 |
| 显示器类型： | LED |
| 配置： | 7 段显示 |
| 数字或字符： | A/D，3.5 位数字 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 40-DIP（0.600"，15.24mm） |
| 供应商设备封装： | 40-DIP |
| 包装： | 管件 |
ICL7106, ICL7107, ICL7107S
Analog COMMON
This pin is included primarily to set the common mode
V+
voltage for battery operation (ICL7106) or for any system
where the input signals are floating with respect to the power
supply. The COMMON pin sets a voltage that is
approximately 2.8V more negative than the positive supply.
This is selected to give a minimum end-of-life battery voltage
of about 6V. However, analog COMMON has some of the
attributes of a reference voltage. When the total supply
voltage is large enough to cause the zener to regulate (>7V),
the COMMON voltage will have a low voltage coefficient
(0.001%/V), low output impedance ( ? 15 ? ), and a
temperature coefficient typically less than 80ppm/× o C.
The limitations of the on chip reference should also be
recognized, however. With the ICL7107, the internal heating
V
REF HI
REF LO
ICL7106
ICL7107
V-
FIGURE 4A.
V+
6.8V
ZENER
I Z
which results from the LED drivers can cause some
degradation in performance. Due to their higher thermal
resistance, plastic parts are poorer in this respect than
V
ICL7106
ICL7107
20k ?
6.8k ?
ceramic. The combination of reference Temperature
Coefficient (TC), internal chip dissipation, and package
thermal resistance can increase noise near full scale from
25 μ V to 80 μ V P-P . Also the linearity in going from a high
dissipation count such as 1000 (20 segments on) to a low
dissipation count such as 1111(8 segments on) can suffer by
REF HI
REF LO
COMMON
ICL8069
1.2V
REFERENCE
a count or more. Devices with a positive TC reference may
require several counts to pull out of an over-range condition.
This is because over-range is a low dissipation mode, with the
three least significant digits blanked. Similarly, units with a
negative TC may cycle between over-range and a non-over-
range count as the die alternately heats and cools. All these
problems are of course eliminated if an external reference is
used.
The ICL7106, with its negligible dissipation, suffers from
none of these problems. In either case, an external reference
can easily be added, as shown in Figure 4.
Analog COMMON is also used as the input low return during
FIGURE 4B.
FIGURE 4. USING AN EXTERNAL REFERENCE
TEST
The TEST pin serves two functions. On the ICL7106 it is
coupled to the internally generated digital supply through a
500 ? resistor. Thus it can be used as the negative supply for
externally generated segment drivers such as decimal points
or any other presentation the user may want to include on
the LCD display. Figures 5 and 6 show such an application.
No more than a 1mA load should be applied.
auto-zero and de-integrate. If IN LO is different from analog
COMMON, a common mode voltage exists in the system
and is taken care of by the excellent CMRR of the converter.
However, in some applications IN LO will be set at a fixed
known voltage (power supply common for instance). In this
application, analog COMMON should be tied to the same
point, thus removing the common mode voltage from the
V+
ICL7106
BP
21
1M ?
TO LCD
DECIMAL
POINT
converter. The same holds true for the reference voltage. If
reference can be conveniently tied to analog COMMON, it
TEST
37
TO LCD
BACKPLANE
should be since this removes the common mode voltage
from the reference system.
Within the lC, analog COMMON is tied to an N-Channel FET
that can sink approximately 30mA of current to hold the
voltage 2.8V below the positive supply (when a load is trying
to pull the common line positive). However, there is only
10 μ A of source current, so COMMON may easily be tied to a
more negative voltage thus overriding the internal reference.
7
FIGURE 5. SIMPLE INVERTER FOR FIXED DECIMAL POINT
The second function is a “lamp test”. When TEST is pulled
high (to V+) all segments will be turned on and the display
should read “1888”. The TEST pin will sink about 15mA
under these conditions.
CAUTION: In the lamp test mode, the segments have a constant DC
voltage (no square-wave). This may burn the LCD display if main-
tained for extended periods.
FN3082.8
相关PDF资料 |
PDF描述 |
|---|---|
| EMM43DRSI | CONN EDGECARD 86POS DIP .156 SLD |
| RBB13DHHN | CONN EDGE DUAL .050 DIP 26 POS |
| ICL7107CM44 | IC ADC 3.5 DIGIT LED 44-MQFP |
| VI-2NY-CV-F1 | CONVERTER MOD DC/DC 3.3V 99W |
| JMK212BJ335MG-T | CAP CER 3.3UF 6.3V 20% X5R 0805 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICL7107SCPLZ | 功能描述:LED显示驱动器 ADC 3 5 DIG LED DRVR COM RoHS:否 制造商:Micrel 数位数量:5 片段数量: 安装风格:SMD/SMT 封装 / 箱体:PLCC-44 工作电源电压:4.75 V to 11 V 最大电源电流:10 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Tube |
| ICL7109 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:N-CHANNEL JFET |
| ICL7109 WAF | 制造商:Harris Corporation 功能描述: |
| ICL71091DL | 制造商:Harris Corporation 功能描述: |
| ICL7109C/D | 功能描述:显示驱动器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。