- 您现在的位置：买卖IC网 > PDF目录67109 > ICS333M-XX-LF 200 MHz, OTHER CLOCK GENERATOR, PDSO8 PDF资料下载
参数资料
| 型号： | ICS333M-XX-LF |
| 元件分类： | 时钟产生/分配 |
| 英文描述： | 200 MHz, OTHER CLOCK GENERATOR, PDSO8 |
| 封装： | 0.150 INCH, SOIC-8 |
| 文件页数： | 3/6页 |
| 文件大小： | 72K |
| 代理商： | ICS333M-XX-LF |
QTClock Triple Output Clock
MDS 333 D
3
Revision 020102
Integrated Circuit Systems, Inc. q 525 Race Street, San Jose, CA 95126 q tel (408) 295-9800 q
www.icst.com
ICS333
External Components
Series Termination Resistor
Clock output traces over one inch should use series
termination. To series terminate a 50
trace (a
commonly used trace impedance), place a 33
resistor
in series with the clock line, as close to the clock output
pin as possible. The nominal impedance of the clock
output is 20
.
Decoupling Capacitor
As with any high performance mixed-signal IC, the
ICS333 must be isolated from system power supply
noise to perform optimally.
A decoupling capacitor of 0.01F must be connected
between VDD and the PCB ground plane.
Crystal Load Capacitors
The device crystal connections should include pads for
small capacitors from X1 to ground and from X2 to
ground. These capacitors are used to adjust the stray
capacitance of the board to match the nominally
required crystal load capacitance. Because load
capacitance can only be increased in this trimming
process, it is important to keep stray capacitance to a
minimum by using very short PCB traces (and no vias)
been the crystal and device. Crystal capacitors must be
connected from each of the pins X1 and X1 to ground.
The value (in pF) of these crystal caps should equal
(CL -6pF)*2. In this equation, CL= crystal load
capacitance in pF. Example: For a crystal with a 16 pF
load capacitance, each crystal capacitor would be 20
pF [(16-6) x 2] = 20.
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed.
1) The 0.01F decoupling capacitor should be mounted
on the component side of the board as close to the
VDD pin as possible. No vias should be used between
decoupling capacitor and VDD pin. The PCB trace to
VDD pin should be kept as short as possible, as should
the PCB trace to the ground via. Distance of the ferrite
bead and bulk decoupling from the device is less
critical.
2) The external crystal should be mounted just next to
the device with short traces. The X1 and X2 traces
should not be routed next to each other with minimum
spaces, instead they should be separated and away
from other traces.
3) To minimize EMI the 33
series termination resistor,
if needed, should be placed close to the clock output.
4) An optimum layout is one with all components on the
same side of the board, minimizing vias through other
signal layers (the ferrite bead and bulk decoupling
capacitor can be mounted on the back). Other signal
traces should be routed away from the ICS333. This
includes signal traces just underneath the device, or on
layers adjacent to the ground plane layer used by the
device.
相关PDF资料 |
PDF描述 |
|---|---|
| ICS345RPLFT | 200 MHz, OTHER CLOCK GENERATOR, PDSO20 |
| ICS345RIP | 200 MHz, OTHER CLOCK GENERATOR, PDSO20 |
| ICS345RIPLF | 200 MHz, OTHER CLOCK GENERATOR, PDSO20 |
| ICS345R-XX | 200 MHz, OTHER CLOCK GENERATOR, PDSO20 |
| ICS345R-XXT | 200 MHz, OTHER CLOCK GENERATOR, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICS341 | 制造商:ICS 制造商全称:ICS 功能描述:Field Programmable SS VersaClock Synthesizer |
| ICS341MIP | 功能描述:IC VERSACLOCK SYNTHESIZER 8-SOIC RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:VersaClock™ 产品变化通告:Product Discontinuation 04/May/2011 标准包装:96 系列:- 类型:时钟倍频器，零延迟缓冲器 PLL:带旁路 输入:LVTTL 输出:LVTTL 电路数:1 比率 - 输入:输出:1:8 差分 - 输入:输出:无/无 频率 - 最大:133.3MHz 除法器/乘法器:是/无 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:管件 其它名称:23S08-5HPGG |
| ICS341MIPLF | 功能描述:IC VERSACLOCK SYNTHESIZER 8-SOIC RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:VersaClock™ 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS，LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:带卷 (TR) |
| ICS341MIPLFT | 功能描述:IC VERSACLOCK SYNTHESIZER 8-SOIC RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:VersaClock™ 标准包装:2,000 系列:- 类型:PLL 频率合成器 PLL:是 输入:晶体 输出:时钟 电路数:1 比率 - 输入:输出:1:1 差分 - 输入:输出:无/无 频率 - 最大:1GHz 除法器/乘法器:是/无 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-LSSOP（0.175"，4.40mm 宽） 供应商设备封装:16-SSOP 包装:带卷 (TR) 其它名称:NJW1504V-TE1-NDNJW1504V-TE1TR |
| ICS341MIPT | 功能描述:IC VERSACLOCK SYNTHESIZER 8-SOIC RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:VersaClock™ 产品变化通告:Product Discontinuation 04/May/2011 标准包装:96 系列:- 类型:时钟倍频器，零延迟缓冲器 PLL:带旁路 输入:LVTTL 输出:LVTTL 电路数:1 比率 - 输入:输出:1:8 差分 - 输入:输出:无/无 频率 - 最大:133.3MHz 除法器/乘法器:是/无 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:管件 其它名称:23S08-5HPGG |
发布紧急采购，3分钟左右您将得到回复。