- 您现在的位置：买卖IC网 > PDF目录8864 > ICS348RP (IDT, Integrated Device Technology Inc)IC CLK SYNTHESIZER QUAD 20-QSOP PDF资料下载
参数资料
| 型号： | ICS348RP |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 3/9页 |
| 文件大小： | 0K |
| 描述： | IC CLK SYNTHESIZER QUAD 20-QSOP |
| 产品变化通告： | Product Discontinuation 13/May/2009 |
| 标准包装： | 55 |
| 系列： | VersaClock™ |
| 类型： | 时钟/频率合成器 |
| PLL： | 带旁路 |
| 输入： | 时钟，晶体 |
| 输出： | LVCMOS |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:9 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 200MHz |
| 除法器/乘法器： | 无/是 |
| 电源电压： | 3.15 V ~ 3.45 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 20-QSOP |
| 包装： | 管件 |
| 其它名称： | 348RP |
ICS348
QUAD PLL FIELD PROGRAMMABLE VERSACLOCK SYNTHESIZER
EPROM CLOCK SYNTHESIZER
IDT / ICS QUAD PLL FIELD PROGRAMMABLE VERSACLOCK SYNTHESIZER 3
ICS348
REV L 051310
External Components
Series Termination Resistor
Clock output traces over one inch should use series
termination. To series terminate a 50
trace (a commonly
used trace impedance), place a 33
resistor in series with
the clock line, as close to the clock output pin as possible.
The nominal impedance of the clock output is 20
.
Decoupling Capacitors
As with any high-performance mixed-signal IC, the ICS348
must be isolated from system power supply noise to perform
optimally.
Decoupling capacitors of 0.01F must be connected
between each VDD and the PCB ground plane.
Crystal Load Capacitors
The device crystal connections should include pads for
small capacitors from X1 to ground and from X2 to ground.
These capacitors are used to adjust the stray capacitance
of the board to match the nominally required crystal load
capacitance. Because load capacitance can only be
increased in this trimming process, it is important to keep
stray capacitance to a minimum by using very short PCB
traces (and no vias) between the crystal and device. Crystal
capacitors must be connected from each of the pins X1 and
X2 to ground.
The value (in pF) of these crystal caps should equal (CL -6
pF)*2. In this equation, CL= crystal load capacitance in pF.
Example: For a crystal with a 16 pF load capacitance, each
crystal capacitor would be 20 pF [(16-6) x 2] = 20.
PCB Layout Recommendations
For optimum device performance and lowest output phase
noise, the following guidelines should be observed.
1) Each 0.01F decoupling capacitor should be mounted on
the component side of the board as close to the VDD pin as
possible. No vias should be used between decoupling
capacitor and VDD pin. The PCB trace to VDD pin should
be kept as short as possible, as should the PCB trace to the
ground via.
2) The external crystal should be mounted just next to the
device with short traces. The X1 and X2 traces should not
be routed next to each other with minimum spaces, instead
they should be separated and away from other traces.
3) To minimize EMI, the 33
series termination resistor, if
needed, should be placed close to the clock output.
4) An optimum layout is one with all components on the
same side of the board, minimizing vias through other signal
layers
ICS348 Configuration Capabilities
The architecture of the ICS348 allows the user to easily
configure the device to a wide range of output frequencies,
for a given input reference frequency.
The frequency multiplier PLL provides a high degree of
precision. The M/N values (the multiplier/divide values
available to generate the target VCO frequency) can be set
within the range of M = 1 to 2048 and N = 1 to 1024.
The ICS348 also provides separate output divide values,
from 2 through 20, to allow the two output clock banks to
support widely differing frequency values from the same
PLL.
Each output frequency can be represented as:
IDT VersaClock Software
IDT applies years of PLL optimization experience into a user
friendly software that accepts the user’s target reference
clock and output frequencies and generates the lowest jitter,
lowest power configuration, with only a press of a button.
The user does not need to have prior PLL experience or
determine the optimal VCO frequency to support multiple
output frequencies.
VersaClock software quickly evaluates accessible VCO
frequencies with available output divide values and provides
an easy to understand, bar code rating for the target output
frequencies. The user may evaluate output accuracy,
performance trade-off scenarios in seconds.
OutputFreq
REFFreq
OutputDivide
--------------------------------------
M
N
-----
=
相关PDF资料 |
PDF描述 |
|---|---|
| MS27473E12F8SALC | CONN HSG PLUG 8POS STRGHT SCKT |
| V24B48M200BG3 | CONVERTER MOD DC/DC 48V 200W |
| CS3102A-40-62S | CONN RCPT 60POS BOX MNT W/SCKT |
| MS3126E14-5PXLC | CONN HSG PLUG 5POS STRGHT PINS |
| MS27484T14B18PLC | CONN HSG PLUG 18POS STRGHT PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICS348RPLF | 功能描述:IC CLK SYNTHESIZER QUAD 20-QSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:VersaClock™ 标准包装:2,000 系列:- 类型:PLL 频率合成器 PLL:是 输入:晶体 输出:时钟 电路数:1 比率 - 输入:输出:1:1 差分 - 输入:输出:无/无 频率 - 最大:1GHz 除法器/乘法器:是/无 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-LSSOP（0.175"，4.40mm 宽） 供应商设备封装:16-SSOP 包装:带卷 (TR) 其它名称:NJW1504V-TE1-NDNJW1504V-TE1TR |
| ICS348RPLFT | 功能描述:IC CLK SYNTHESIZER QUAD 20-QSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:VersaClock™ 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS，LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:带卷 (TR) |
| ICS348RPT | 功能描述:IC CLK SYNTHESIZER QUAD 20-QSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:VersaClock™ 产品变化通告:Product Discontinuation 04/May/2011 标准包装:96 系列:- 类型:时钟倍频器，零延迟缓冲器 PLL:带旁路 输入:LVTTL 输出:LVTTL 电路数:1 比率 - 输入:输出:1:8 差分 - 输入:输出:无/无 频率 - 最大:133.3MHz 除法器/乘法器:是/无 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:管件 其它名称:23S08-5HPGG |
| ICS348T | 制造商:ADAM-TECH 制造商全称:Adam Technologies, Inc. 功能描述:IC SOCKETS SINGLE & DUAL ROW SOCKETS |
| ICS3726-02 | 制造商:ICS 制造商全称:ICS 功能描述:HIGH PERFORMANCE VCXO |
发布紧急采购，3分钟左右您将得到回复。