- 您现在的位置：买卖IC网 > PDF目录2074 > ICS853S006AGILF (IDT, Integrated Device Technology Inc)IC CLOCK BUFFER 1:6 2GHZ 20TSSOP PDF资料下载
参数资料
| 型号： | ICS853S006AGILF |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 2/19页 |
| 文件大小： | 0K |
| 描述： | IC CLOCK BUFFER 1:6 2GHZ 20TSSOP |
| 特色产品： | IDT - ?LVPECL Buffer |
| 标准包装： | 74 |
| 系列： | HiPerClockS™ |
| 类型： | 扇出缓冲器（分配） |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:6 |
| 差分 - 输入:输出： | 是/是 |
| 输入： | CML，LVDS，LVPECL，SSTL |
| 输出： | ECL，PECL |
| 频率 - 最大： | 2GHz |
| 电源电压： | 2.375 V ~ 3.465 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
| 其它名称： | 800-2247 |
ICS853S006I Data Sheet
LOW SKEW, 1-TO-6, DIFFERENTIAL-TO-2.5V, 3.3V LVPECL/ECL FANOUT BUFFER
ICS853S006AGI REVISION A NOVEMBER 15, 2011
10
2011 Integrated Device Technology, Inc.
Application Information
Wiring the Differential Input to Accept Single-Ended Levels
Figure 1 shows how a differential input can be wired to accept single
ended levels. The reference voltage VREF = VCC/2 is generated by
the bias resistors R1 and R2. The bypass capacitor (C1) is used to
help filter noise on the DC bias. This bias circuit should be located as
close to the input pin as possible. The ratio of R1 and R2 might need
to be adjusted to position the VREF in the center of the input voltage
swing. For example, if the input clock swing is 2.5V and VCC = 3.3V,
R1 and R2 value should be adjusted to set VREF at 1.25V. The values
below are for when both the single ended swing and VCC are at the
same voltage. This configuration requires that the sum of the output
impedance of the driver (Ro) and the series resistance (Rs) equals
the transmission line impedance. In addition, matched termination at
the input will attenuate the signal in half. This can be done in one of
two ways. First, R3 and R4 in parallel should equal the transmission
line impedance. For most 50
Ω applications, R3 and R4 can be 100Ω.
The values of the resistors can be increased to reduce the loading for
slower and weaker LVCMOS driver. When using single-ended
signaling, the noise rejection benefits of differential signaling are
reduced. Even though the differential input can handle full rail
LVCMOS signaling, it is recommended that the amplitude be
reduced. The datasheet specifies a lower differential amplitude,
however this only applies to differential signals. For single-ended
applications, the swing can be larger, however VIL cannot be less
than -0.3V and VIH cannot be more than VCC + 0.3V. Though some
of the recommended components might not be used, the pads should
be placed in the layout. They can be utilized for debugging purposes.
The datasheet specifications are characterized and guaranteed by
using a differential signal.
Figure 1. Recommended Schematic for Wiring a Differential Input to Accept Single-ended Levels
相关PDF资料 |
PDF描述 |
|---|---|
| ICS853S011BGILF | IC CLK BUFFER 1:2 2.5GHZ 8-TSSOP |
| ICS853S013AMILF | IC CLOCK BUFFER 1:3 2GHZ 20-SOIC |
| ICS853S024AYLF | IC CLK BUFF 1:24 1.5GHZ 64-TQFP |
| ICS853S111AYILF | IC CLOCK BUFFER MUX 2:10 32-LQFP |
| ICS85408BGILFT | IC CLK BUFF 1:8 700MHZ 24-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICS853S006AGILFT | 制造商:Integrated Device Technology Inc 功能描述:IC CLK BUFFER 1:6 2GHZ 20TSSOP |
| ICS853S011BGILF | 功能描述:IC CLK BUFFER 1:2 2.5GHZ 8-TSSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟缓冲器，驱动器 系列:HiPerClockS™ 标准包装:74 系列:- 类型:扇出缓冲器（分配） 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 输入:HCSL, LVCMOS, LVDS, LVPECL, LVTTL 输出:HCSL，LVDS 频率 - 最大:400MHz 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:32-VFQFN 裸露焊盘 供应商设备封装:32-QFN（5x5） 包装:管件 |
| ICS853S011BGILFT | 功能描述:IC CLK BUFFER 1:2 2.5GHZ 8-TSSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟缓冲器，驱动器 系列:HiPerClockS™ 标准包装:74 系列:- 类型:扇出缓冲器（分配） 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 输入:HCSL, LVCMOS, LVDS, LVPECL, LVTTL 输出:HCSL，LVDS 频率 - 最大:400MHz 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:32-VFQFN 裸露焊盘 供应商设备封装:32-QFN（5x5） 包装:管件 |
| ICS853S011BMILF | 功能描述:IC CLOCK BUFFER 1:2 2.5GHZ 8SOIC RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟缓冲器，驱动器 系列:HiPerClockS™ 产品培训模块:High Bandwidth Product Overview 标准包装:1,000 系列:Precision Edge® 类型:扇出缓冲器（分配） 电路数:1 比率 - 输入:输出:1:4 差分 - 输入:输出:是/是 输入:CML，LVDS，LVPECL 输出:CML 频率 - 最大:2.5GHz 电源电压:2.375 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VFQFN 裸露焊盘，16-MLF? 供应商设备封装:16-MLF?（3x3） 包装:带卷 (TR) |
| ICS853S011BMILFT | 功能描述:IC CLOCK BUFFER 1:2 2.5GHZ 8SOIC RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟缓冲器，驱动器 系列:HiPerClockS™ 标准包装:74 系列:- 类型:扇出缓冲器（分配） 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 输入:HCSL, LVCMOS, LVDS, LVPECL, LVTTL 输出:HCSL，LVDS 频率 - 最大:400MHz 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:32-VFQFN 裸露焊盘 供应商设备封装:32-QFN（5x5） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。