- 您现在的位置：买卖IC网 > PDF目录67704 > ICS87993AYIT 87993 SERIES, PLL BASED CLOCK DRIVER, 5 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PQFP32 PDF资料下载
参数资料
| 型号： | ICS87993AYIT |
| 元件分类： | 时钟及定时 |
| 英文描述： | 87993 SERIES, PLL BASED CLOCK DRIVER, 5 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PQFP32 |
| 封装： | 7 X 7 MM, 1.40 MM HEIGHT, MS-026, LQFP-32 |
| 文件页数： | 2/16页 |
| 文件大小： | 199K |
| 代理商： | ICS87993AYIT |
87993AYI
www.icst.com/products/hiperclocks.html
REV. B OCTOBER 21, 2004
10
Integrated
Circuit
Systems, Inc.
ICS87993I
1-TO-5 DIFFERENTIAL-TO-3.3V LVPECL
PLL CLOCK DRIVER W/DYNAMIC CLOCK SWITCH
C4
50 Ohm
Traces
C3
VCCA
C1
GND
R7
C2
VCC
C11
U1
VIA
Pin 1
C16
FIGURE 5B. PCB BOARD LAYOUT FOR ICS87993I
The following component footprints are used in this layout
example:
All the resistors and capacitors are size 0603.
POWER AND GROUNDING
Place the decoupling capacitors as close as possible to the power
pins. If space allows, placement of the decoupling capacitor on
the component side is preferred. This can reduce unwanted in-
ductance between the decoupling capacitor and the power pin
caused by the via.
Maximize the power and ground pad sizes and number of vias
capacitors. This can reduce the inductance between the power
and ground planes and the component power and ground pins.
The RC filter consisting of R7, C11, and C16 should be placed
as close to the V
DDA pin as possible.
CLOCK TRACES AND TERMINATION
Poor signal integrity can degrade the system performance or
cause system failure. In synchronous high-speed digital systems,
the clock signal is less tolerant to poor signal integrity than other
signals. Any ringing on the rising or falling edge or excessive ring
back can cause system failure. The shape of the trace and the
trace delay might be restricted by the available space on the board
and the component location. While routing the traces, the clock
signal traces should be routed first and should be locked prior to
routing other signal traces.
The differential 50
output traces should have same
length.
Avoid sharp angles on the clock trace. Sharp angle turns
cause the characteristic impedance to change on the
transmission lines.
Keep the clock traces on the same layer. Whenever pos-
sible, avoid placing vias on the clock traces. Placement
of vias on the traces can affect the trace characteristic
impedance and hence degrade signal integrity.
To prevent cross talk, avoid routing other signal traces in
parallel with the clock traces. If running parallel traces is
unavoidable, allow a separation of at least three trace
widths between the differential clock trace and the other
signal trace.
Make sure no other signal traces are routed between the
clock trace pair.
The series termination resistors should be located as close
to the driver pins as possible.
相关PDF资料 |
PDF描述 |
|---|---|
| ICS87993AYILF | 87993 SERIES, PLL BASED CLOCK DRIVER, 5 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PQFP32 |
| ICS87993AYILFT | 87993 SERIES, PLL BASED CLOCK DRIVER, 5 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PQFP32 |
| ICS889474AKLFT | 889474 SERIES, LOW SKEW CLOCK DRIVER, 2 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), QCC24 |
| ICS889831AKLFT | 889831 SERIES, LOW SKEW CLOCK DRIVER, 4 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), QCC16 |
| ICS889834AK | 889834 SERIES, LOW SKEW CLOCK DRIVER, 4 TRUE OUTPUT(S), 4 INVERTED OUTPUT(S), QCC16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ICS889474AKLF | 功能描述:IC CLK BUFFER MUX 2:2 24-VFQFPN RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟缓冲器，驱动器 系列:HiPerClockS™ 标准包装:74 系列:- 类型:扇出缓冲器（分配） 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 输入:HCSL, LVCMOS, LVDS, LVPECL, LVTTL 输出:HCSL，LVDS 频率 - 最大:400MHz 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:32-VFQFN 裸露焊盘 供应商设备封装:32-QFN（5x5） 包装:管件 |
| ICS889474AKLFT | 功能描述:IC CLK BUFFER MUX 2:2 24-VFQFPN RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟缓冲器，驱动器 系列:HiPerClockS™ 标准包装:74 系列:- 类型:扇出缓冲器（分配） 电路数:1 比率 - 输入:输出:1:10 差分 - 输入:输出:是/是 输入:HCSL, LVCMOS, LVDS, LVPECL, LVTTL 输出:HCSL，LVDS 频率 - 最大:400MHz 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:32-VFQFN 裸露焊盘 供应商设备封装:32-QFN（5x5） 包装:管件 |
| ICS889831AKLF | 功能描述:IC CLK BUFF 1:4 2.1GHZ 16-VFQFPN RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟缓冲器，驱动器 系列:HiPerClockS™ 标准包装:1 系列:HiPerClockS™ 类型:扇出缓冲器（分配），多路复用器 电路数:1 比率 - 输入:输出:2:18 差分 - 输入:输出:是/无 输入:CML，LVCMOS，LVPECL，LVTTL，SSTL 输出:LVCMOS，LVTTL 频率 - 最大:250MHz 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:- 其它名称:800-1923-6 |
| ICS889831AKLFT | 功能描述:IC CLK BUFF 1:4 2.1GHZ 16-VFQFPN RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟缓冲器，驱动器 系列:HiPerClockS™ 标准包装:1 系列:HiPerClockS™ 类型:扇出缓冲器（分配），多路复用器 电路数:1 比率 - 输入:输出:2:18 差分 - 输入:输出:是/无 输入:CML，LVCMOS，LVPECL，LVTTL，SSTL 输出:LVCMOS，LVTTL 频率 - 最大:250MHz 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:- 其它名称:800-1923-6 |
| ICS889832AKLF | 功能描述:IC CLK BUFFER 1:4 2GHZ 16-VFQFPN RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟缓冲器，驱动器 系列:HiPerClockS™ 标准包装:1 系列:HiPerClockS™ 类型:扇出缓冲器（分配），多路复用器 电路数:1 比率 - 输入:输出:2:18 差分 - 输入:输出:是/无 输入:CML，LVCMOS，LVPECL，LVTTL，SSTL 输出:LVCMOS，LVTTL 频率 - 最大:250MHz 电源电压:2.375 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:- 其它名称:800-1923-6 |
发布紧急采购，3分钟左右您将得到回复。