- 您现在的位置：买卖IC网 > Datasheet目录328 > IDT7019L20PFI (IDT, Integrated Device Technology Inc)IC SRAM 1.125MBIT 20NS 100TQFP Datasheet资料下载
参数资料
| 型号： | IDT7019L20PFI |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 15/17页 |
| 文件大小： | 0K |
| 描述： | IC SRAM 1.125MBIT 20NS 100TQFP |
| 标准包装： | 6 |
| 格式 - 存储器： | RAM |
| 存储器类型： | SRAM - 双端口，异步 |
| 存储容量： | 1.125M（128K x 9） |
| 速度： | 20ns |
| 接口： | 并联 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-TQFP（14x14） |
| 包装： | 托盘 |
| 其它名称： | 7019L20PFI |
IDT7019L
High-Speed 128K x 9 Dual-Port Static RAM
Busy Logic
Busy Logic provides a hardware indication that both ports of the RAM
have accessed the same location at the same time. It also allows one of the
two accesses to proceed and signals the other side that the RAM is “busy”.
The BUSY pin can then be used to stall the access until the operation on
the other side is completed. If a write operation has been attempted from
the side that receives a BUSY indication, the write signal is gated internally
to prevent the write from proceeding.
The use of BUSY logic is not required or desirable for all applications.
In some cases it may be useful to logically OR the BUSY outputs together
and use any BUSY indication as an interrupt source to flag the event of
an illegal or illogical operation. If the write inhibit function of BUSY logic is
not desirable, the BUSY logic can be disabled by placing the part in slave
mode with the M/ S pin. Once in slave mode the BUSY pin operates solely
as a write inhibit input pin. Normal operation can be programmed by tying
the BUSY pins HIGH. If desired, unintended write operations can be
prevented to a port by tying the BUSY pin for that port LOW.
The BUSY outputs on the IDT7019 RAM in master mode, are push-
pull type outputs and do not require pull up resistors to operate. If these
RAMs are being expanded in depth, then the BUSY indication for the
resulting array requires the use of an external AND gate.
A 17
Industrial and Commercial Temperature Ranges
can result in a glitched internal write inhibit signal and corrupted data
in the slave.
Semaphores
The IDT7019 is an extremely fast Dual-Port 128K x 9 CMOS Static
RAM with an additional 8 address locations dedicated to binary semaphore
flags. These flags allow either processor on the left or right side of the Dual-
Port RAM to claim a privilege over the other processor for functions defined
by the system designer’s software. As an example, the semaphore can
be used by one processor to inhibit the other from accessing a portion of
the Dual-Port RAM or any other shared resource.
The Dual-Port RAM features a fast access time, and both ports are
completely independent of each other. This means that the activity on the
left port in no way slows the access time of the right port. Both ports are
identical in function to standard CMOS Static RAM and can be read from,
or written to, at the same time with the only possible conflict arising from the
simultaneous writing of, or a simultaneous READ/WRITE of, a non-
semaphore location. Semaphores are protected against such ambiguous
situations and may be used by the system program to avoid any conflicts
in the non-semaphore portion of the Dual-Port RAM. These devices have
an automatic power-down feature controlled by CE , the Dual-Port RAM
enable, and SEM , the semaphore enable. The CE and SEM pins control
MASTER
Dual Port RAM
CE 0
SLAVE
Dual Port RAM
CE 0
on-chip power down circuitry that permits the respective port to go into
standby mode when not selected. This is the condition which is shown in
BUSY L
BUSY R
BUSY L
BUSY R
Truth Table II where CE and SEM are both HIGH.
Systems which can best use the IDT7019 contain multiple processors
Dual Port RAM
BUSY L BUSY R
MASTER CE 1
Dual Port RAM
BUSY L BUSY R
SLAVE CE 1
,
or controllers and are typically very high-speed systems which are
software controlled or software intensive. These systems can benefit
from a performance increase offered by the IDT7019s hardware
semaphores, which provide a lockout mechanism without requiring
4840 drw 17
Figure 3. Busy and chip enable routing for both width and depth
expansion with IDT7019 RAMs.
Width Expansion Busy Logic
Master/Slave Arrays
When expanding an IDT7019 RAM array in width while using BUSY
logic, one master part is used to decide which side of the RAMs array will
receive a BUSY indication, and to output that indication. Any number of
slaves to be addressed in the same address range as the master, use
the BUSY signal as a write inhibit signal. Thus on the IDT7019 RAM the
BUSY pin is an output if the part is used as a master (M/ S pin = V IH ), and
the BUSY pin is an input if the part used as a slave (M/ S pin = V IL ) as shown
in Figure 3.
If two or more master parts were used when expanding in width, a split
decision could result with one master indicating BUSY on one side of the
array and another master indicating BUSY on one other side of the array.
This would inhibit the write operations from one port for part of a word and
inhibit the write operations from the other port for the other part of the word.
The BUSY arbitration, on a master, is based on the chip enable and
address signals only. It ignores whether an access is a read or write. In
a master/slave array, both address and chip enable must be valid long
enough for a BUSY flag to be output from the master before the actual
write pulse can be initiated with the R/ W signal. Failure to observe this timing
complex programming.
Software handshaking between processors offers the maximum in
system flexibility by permitting shared resources to be allocated in varying
configurations. The IDT7019 does not use its semaphore flags to control
any resources through hardware, thus allowing the system designer total
flexibility in system architecture.
An advantage of using semaphores rather than the more common
methods of hardware arbitration is that wait states are never incurred in
either processor. This can prove to be a major advantage in very high-
speed systems.
How the Semaphore Flags Work
The semaphore logic is a set of eight latches which are independent
of the Dual-Port RAM. These latches can be used to pass a flag, or token,
from one port to the other to indicate that a shared resource is in use. The
semaphores provide a hardware assist for a use assignment method
called “Token Passing Allocation.” In this method, the state of a semaphore
latch is used as a token indicating that shared resource is in use. If the left
processor wants to use this resource, it requests the token by setting the
latch. This processor then verifies its success in setting the latch by reading
it. If it was successful, it proceeds to assume control over the shared
resource. If it was not successful in setting the latch, it determines that the
right side processor has set the latch first, has the token and is using the
shared resource. The left processor can then either repeatedly request
that semaphore’s status or remove its request for that semaphore to perform
15
6.42
相关PDF资料 |
PDF描述 |
|---|---|
| IDT7024L55G | IC SRAM 64KBIT 55NS 84PGA |
| IDT7025L55G | IC SRAM 128KBIT 55NS 84PGA |
| IDT70261L20PFI | IC SRAM 256KBIT 20NS 100TQFP |
| IDT7026L20G | IC SRAM 256KBIT 20NS 84PGA |
| IDT7027L25G | IC SRAM 512KBIT 25NS 108PGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT7019L20PFI8 | 功能描述:IC SRAM 1.125MBIT 20NS 100TQFP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1,000 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 双端口，同步 存储容量:1.125M（32K x 36） 速度:5ns 接口:并联 电源电压:3.15 V ~ 3.45 V 工作温度:-40°C ~ 85°C 封装/外壳:256-LBGA 供应商设备封装:256-CABGA（17x17） 包装:带卷 (TR) 其它名称:70V3579S5BCI8 |
| IDT7024L15J | 功能描述:IC SRAM 64KBIT 15NS 84PLCC RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:45 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 双端口，异步 存储容量:128K（8K x 16） 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:100-LQFP 供应商设备封装:100-TQFP（14x14） 包装:托盘 其它名称:70V25S15PF |
| IDT7024L15J8 | 功能描述:IC SRAM 64KBIT 15NS 84PLCC RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:45 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 双端口，异步 存储容量:128K（8K x 16） 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:100-LQFP 供应商设备封装:100-TQFP（14x14） 包装:托盘 其它名称:70V25S15PF |
| IDT7024L15JG | 功能描述:IC SRAM 64KBIT 15NS 84PLCC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:45 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 双端口，异步 存储容量:128K（8K x 16） 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:100-LQFP 供应商设备封装:100-TQFP（14x14） 包装:托盘 其它名称:70V25S15PF |
| IDT7024L15JG8 | 功能描述:IC SRAM 64KBIT 15NS 84PLCC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:45 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 双端口，异步 存储容量:128K（8K x 16） 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:100-LQFP 供应商设备封装:100-TQFP（14x14） 包装:托盘 其它名称:70V25S15PF |
发布紧急采购，3分钟左右您将得到回复。