- 您现在的位置：买卖IC网 > PDF目录10009 > IDT72V233L6BC (IDT, Integrated Device Technology Inc)IC FIFO 1024X18 6NS 100BGA PDF资料下载
参数资料
| 型号： | IDT72V233L6BC |
| 厂商： | IDT, Integrated Device Technology Inc |
| 文件页数： | 11/45页 |
| 文件大小： | 0K |
| 描述： | IC FIFO 1024X18 6NS 100BGA |
| 标准包装： | 1 |
| 系列： | 72V |
| 功能： | 异步，同步 |
| 存储容量： | 18.4K（1K x 18） |
| 数据速率： | 166MHz |
| 访问时间： | 4ns |
| 电源电压： | 3.15 V ~ 3.45 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LBGA |
| 供应商设备封装： | 100-CABGA（11x11） |
| 包装： | 托盘 |
| 其它名称： | 72V233L6BC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
19
IDT72V263/273/283/293/103/113 3.3V HIGH DENSITY SUPERSYNC IITM NARROW BUS FIFO
8K x 18, 16K x 9/18, 32K x 9/18, 64K x 9/18, 128K x 9/18, 256K x 9/18, 512K x9
COMMERCIAL AND INDUSTRIAL
TEMPERATURE RANGES
IDT72V223/233/243/253/263/273/283/293 3.3V HIGH DENSITY SUPERSYNC IITM NARROW BUS FIFO
512 x 18, 1K x 9/18, 2K x 9/18, 4K x 9/18, 8K x 9/18, 16K x 9/18, 32K x 9/18, 64K x 9/18, 128K x 9
FEBRUARY 11, 2009
SIGNAL DESCRIPTION
INPUTS:
DATA IN (D0 - Dn)
Data inputs for 18-bit wide data (D0-D17) or data inputs for 9-bit wide data
(D0-D8).
CONTROLS:
MASTER RESET (
MRS)
AMasterResetisaccomplishedwheneverthe
MRSinputistakentoaLOW
state.Thisoperationsetstheinternalreadandwritepointerstothefirstlocation
of the RAM array.
PAE will go LOW, PAF will go HIGH, and HF will go HIGH.
IfFWFT/SIisLOWduringMasterResetthentheIDTStandardmode,along
with
EF and FF are selected. EF will go LOW and FF will go HIGH. If FWFT/
SI is HIGH, then the First Word Fall Through mode (FWFT), along with
IRand
OR, are selected. OR will go HIGH and IR will go LOW.
AllcontrolsettingssuchasOW,IW,
BE,RM,PFMandIParedefinedduring
the Master Reset cycle.
DuringaMasterReset,theoutputregisterisinitializedtoallzeroes.AMaster
Reset is required after power up, before a write operation can take place.
MRS
is asynchronous.
See Figure 5, Master Reset Timing, for the relevant timing diagram.
PARTIAL RESET (
PRS)
APartialResetisaccomplishedwheneverthe
PRSinputistakentoaLOW
state. As in the case of the Master Reset, the internal read and write pointers
are set to the first location of the RAM array,
PAEgoesLOW,PAFgoesHIGH,
and
HF goes HIGH.
Whichever mode is active at the time of Partial Reset, IDT Standard mode
or First Word Fall Through, that mode will remain selected. If the IDT Standard
mode is active, then
FFwillgoHIGHandEFwillgoLOW.IftheFirstWordFall
Through mode is active, then
OR will go HIGH, and IR will go LOW.
Following Partial Reset, all values held in the offset registers remain
unchanged. The programming method (parallel or serial) currently active at
the time of Partial Reset is also retained. The output register is initialized to all
zeroes.
PRS is asynchronous.
A Partial Reset is useful for resetting the device during the course of
operation,whenreprogrammingprogrammableflagoffsetsettingsmaynotbe
convenient.
See Figure 6, Partial Reset Timing, for the relevant timing diagram.
ASYNCHRONOUS WRITE (
ASYW)
The write port can be configured for either Synchronous or Asynchronous
mode of operation. If during Master Reset the
ASYW input is LOW, then
Asynchronous operation of the write port will be selected. During Asynchro-
nous operation of the write port the WCLK input becomes WR input, this is the
Asynchronous write strobe input. A rising edge on WR will write data present
on the Dn inputs into the FIFO. (
WEN mustbetiedLOWwhenusingthewrite
port in Asynchronous mode).
When the write port is configured for Asynchronous operation the full flag
(
FF)operatesinanasynchronousmanner,thatis,thefullflagwillbeupdated
based in both a write operation and read operation. Note, if Asynchronous
mode is selected, FWFT is not permissable. Refer to Figures 23, 24, 27 and
28 for relevant timing and operational waveforms.
ASYNCHRONOUS READ (
ASYR)
The read port can be configured for either Synchronous or Asynchronous
mode of operation. If during a Master Reset the
ASYR input is LOW, then
Asynchronousoperationofthereadportwillbeselected.DuringAsynchronous
operation of the read port the RCLK input becomes RD input, this is the
Asynchronous read strobe input. A rising edge on RD will read data from the
FIFO via the output register and Qn port. (
REN must be tied LOW during
Asynchronous operation of the read port).
The
OE input provides three-state control of the Qn output bus, in an
asynchronous manner.
When the read port is configured for Asynchronous operation the device
must be operating on IDT standard mode, FWFT mode is not permissible if the
readportisAsynchronous.TheEmptyFlag(
EF)operatesinanAsynchronous
manner, that is, the empty flag will be updated based on both a read operation
and a write operation. Refer to figures 25, 26, 27 and 28 for relevant timing and
operational waveforms.
RETRANSMIT (
RT)
The Retransmit operation allows data that has already been read to be
accessed again. There are 2 modes of Retransmit operation, normal latency
and zero latency. There are two stages to Retransmit: first, a setup procedure
that resets the read pointer to the first location of memory, then the actual
retransmit, which consists of reading out the memory contents, starting at the
beginning of the memory.
Retransmitsetupisinitiatedbyholding
RTLOWduringarisingRCLKedge.
REN and WEN must be HIGH before bringing RT LOW. When zero latency
is utilized,
REN does not need to be HIGH before bringing RT LOW.
If IDT Standard mode is selected, the FIFO will mark the beginning of the
Retransmitsetupbysetting
EFLOW.Thechangeinlevelwillonlybenoticeable
if
EF was HIGH before setup. During this period, the internal read pointer is
initialized to the first location of the RAM array.
When
EF goesHIGH, Retransmit setupiscompleteand read operations
may begin starting with the first location in memory. Since IDT Standard mode
isselected,everywordreadincludingthefirstwordfollowingRetransmitsetup
requires a LOW on
REN to enable the rising edge of RCLK. See Figure 11,
Retransmit Timing (IDT Standard Mode), for the relevant timing diagram.
IfFWFTmodeisselected,theFIFOwillmarkthebeginningoftheRetransmit
setup by setting
OR HIGH. During this period, the internal read pointer is set
to the first location of the RAM array.
When
ORgoesLOW,Retransmitsetupiscomplete;atthesametime,the
contentsofthefirstlocationappearontheoutputs.SinceFWFTmodeisselected,
the first word appears on the outputs, no LOW on
RENisnecessary.Reading
all subsequent words requires a LOW on
REN to enable the rising edge of
RCLK.SeeFigure12, RetransmitTiming(FWFTMode),fortherelevanttiming
diagram.
In Retransmit operation, zero-latency mode can be selected using the
Retransmit Mode (RM) pin during a Master Reset. This can be applied to both
IDT Standard mode and FWFT mode.
RETRANSMIT LATENCY MODE (RM)
Azero-latencyretransmittimingmodecanbeselectedusingtheRetransmit
timing Mode pin (RM). During Master Reset, a LOW on RM will select zero-
latency retransmit. A HIGH on RM during Master Reset will select normal
latency.
If zero-latency retransmit operation is selected the first data word to be
retransmittedwillbeplacedontheoutputregisterwithrespecttothesameRCLK
edge that initiated the retransmit based on RT being LOW.
Refer to Figure 13 for Retransmit Timing with zero latency (IDT Standard
Mode). Refer to Figure 14 for Retransmit Timing with zero latency (FWFT
Mode).
相关PDF资料 |
PDF描述 |
|---|---|
| VI-24Z-IU-F2 | CONVERTER MOD DC/DC 2V 80W |
| LTC1334CG#TR | IC TXRX CMOS MULTIPROTOCL 28SSOP |
| LTC1543CG#PBF | IC TXRX SOFTWARE SELECTBL 28SSOP |
| LTC1543CG | IC TXRX SOFTWARE SELECTBL 28SSOP |
| LTC2845IUHF#TR | IC TXRX 3.3V MULTIPROTOCOL 38QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IDT72V233L6PF | 功能描述:IC FIFO 1024X18 6NS 80QFP RoHS:否 类别:集成电路 (IC) >> 逻辑 - FIFO 系列:72V 标准包装:90 系列:7200 功能:同步 存储容量:288K（16K x 18） 数据速率:100MHz 访问时间:10ns 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:64-LQFP 供应商设备封装:64-TQFP（14x14） 包装:托盘 其它名称:72271LA10PF |
| IDT72V233L6PF8 | 功能描述:IC FIFO 1024X18 6NS 80QFP RoHS:否 类别:集成电路 (IC) >> 逻辑 - FIFO 系列:72V 标准包装:90 系列:7200 功能:同步 存储容量:288K（16K x 18） 数据速率:100MHz 访问时间:10ns 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:64-LQFP 供应商设备封装:64-TQFP（14x14） 包装:托盘 其它名称:72271LA10PF |
| IDT72V233L7-5BC | 功能描述:IC FIFO 1024X18 7-5NS 100BGA RoHS:否 类别:集成电路 (IC) >> 逻辑 - FIFO 系列:72V 标准包装:90 系列:7200 功能:同步 存储容量:288K（16K x 18） 数据速率:100MHz 访问时间:10ns 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:64-LQFP 供应商设备封装:64-TQFP（14x14） 包装:托盘 其它名称:72271LA10PF |
| IDT72V233L7-5BCI | 功能描述:IC FIFO 1024X18 7-5NS 100BGA RoHS:否 类别:集成电路 (IC) >> 逻辑 - FIFO 系列:72V 标准包装:90 系列:7200 功能:同步 存储容量:288K（16K x 18） 数据速率:100MHz 访问时间:10ns 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:64-LQFP 供应商设备封装:64-TQFP（14x14） 包装:托盘 其它名称:72271LA10PF |
| IDT72V233L7-5PF | 功能描述:IC FIFO 1024X18 7-5NS 80QFP RoHS:否 类别:集成电路 (IC) >> 逻辑 - FIFO 系列:72V 标准包装:90 系列:7200 功能:同步 存储容量:288K（16K x 18） 数据速率:100MHz 访问时间:10ns 电源电压:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:64-LQFP 供应商设备封装:64-TQFP（14x14） 包装:托盘 其它名称:72271LA10PF |
发布紧急采购，3分钟左右您将得到回复。