- 您现在的位置：买卖IC网 > PDF目录1925 > IL3522E (NVE Corp/Isolation Products)IC DIFFER BUS TRANSC 16 SOIC PDF资料下载
参数资料
| 型号： | IL3522E |
| 厂商： | NVE Corp/Isolation Products |
| 文件页数： | 2/15页 |
| 文件大小： | 0K |
| 描述： | IC DIFFER BUS TRANSC 16 SOIC |
| 产品培训模块： | IsoLoop® Isolator |
| 标准包装： | 50 |
| 系列： | IsoLoop® |
| 类型： | 收发器，隔离式 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RS422 |
| 电源电压： | 3 V ~ 5.5 V，4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 管件 |
| 其它名称： | Q3077370 |
IL3522
10
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
NVE Corporation
Fail-Safe Operation
“Fail-safe operation” is defined here as the forcing of a logic high state on the “R” output in response to an open-circuit condition between the
“A” and “B” lines of the bus, or when no drivers are active on the bus.
Proper biasing can ensure fail-safe operation, that is a known state when there are no active drivers on the bus. IL3000-Series Isolated
Transceivers include internal pull-up and pull-down resistors of approximately 30 k in the receiver section (RFS-INT; see figure below). These
internal resistors are designed to ensure failsafe operation but only if there are no termination resistors. The entire VDD will appear between inputs
“A” and “B” if there is no loading and no termination resistors, and there will be more than the required 200 mV with up to four RS-422 worst-
case Unit Loads of 12 k. Many designs operating below 1 Mbps or less than 1,000 feet are unterminated. Termination resistors may not be
necessary for very low data rates and very short cable runs because reflections have time to settle before data sampling, which occurs at the
middle of the bit interval.
In busses with low-impedance termination resistors, however, the differential voltage across the conductor pair will be close to zero with no
active drivers. In this case the state of the bus is indeterminate, and the idle bus will be susceptible to noise. For example, with 120 termination
resistors (RT) on each end of the cable, and four Unit Loads (12 k each), without external fail-safe biasing resistors the internal pull-up and pull-
down resistors will produce a voltage between inputs “A” and “B” of only about 5 mV. This is not nearly enough to ensure a known state.
External fail-safe biasing resistors (RFS-EXT) at one end of the bus can ensure fail-safe operation with a terminated bus. Resistors should be
selected so that under worst-case power supply and resistor tolerances there is at least 200 mV across the conductor pair with no active drivers to
meet the input sensitivity specification of the RS-422 standard.
Using the same value for pull-up and pull-down biasing resistors maintains balance for positive- and negative going transitions. Lower-value
resistors increase inactive noise immunity at the expense of quiescent power consumption. Note that each Unit Load on the bus adds a worst-case
loading of 12 k across the conductor pair, and 32 Unit Loads add 375 worst-case loading. The more loads on the bus, the lower the required
values of the biasing resistors.
In the example with two 120 termination resistors and four Unit Loads, 560 external biasing resistors provide more than 200 mV between
“A” and “B” with adequate margin for power supply variations and resistor tolerances. This ensures a known state when there are no active
drivers. Other illustrative examples are shown in the table below:
Fail-Safe Biasing
R
B
V
DD
30K
GND
A
5 V
R
FS-EXT
R
T
R
T
R
FS-EXT
R
FS-INT
R
FS-INT
Fail-Safe
RT
Loading
Operation?
None
Four unit loads (12 k ea.)
238 mV
Yes
120
Four unit loads (12 k ea.)
5 mV
No
560
120
Four unit loads (12 k ea.)
254 mV
Yes
510
120
32 unit loads (12 k ea.)
247 mV
Yes
Nominal VA-B
(inactive)
RFS-EXT
Internal Only
相关PDF资料 |
PDF描述 |
|---|---|
| IL3585 | ISOLATOR PROFIB 485 XCVR 16SOICW |
| IL3685E | PROFIBUS RS-485 INTERFACE ISO |
| IL41050TE | IC TXRX ISOLATED CAN HS 16SOIC |
| IL422-3V | ISOLATOR HS MAGNETC RS422 16SOIC |
| IL485E-3V | ISOLATOR HS MAG DIGITAL 16SOICW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IL3522ETR13 | 功能描述:IC DIFFER BUS TRANSC 16 SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:IsoLoop® 标准包装:1,240 系列:GD 类型:收发器 驱动器/接收器数:3/5 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:20-DIP（0.300"，7.62mm） 供应商设备封装:20-PDIP 包装:管件 |
| IL3522VE | 功能描述:RS422, RS485 Digital Isolator 6000Vrms 3 Channel 40Mbps 30kV/μs CMTI 16-SOIC (0.295", 7.50mm Width) 制造商:nve corp/isolation products 系列:IsoLoop? 包装:管件 零件状态:有效 技术:GMR（大型磁阻传感） 类型:RS422，RS485 隔离式电源:无 通道数:3 输入 - 输入侧 1/输入侧 2:2/1 通道类型:单向 电压 - 隔离:6000Vrms 共模瞬态抗扰度（最小值）:30kV/μs 数据速率:40Mbps 传播延迟 tpLH / tpHL（最大值）:35ns，35ns 脉宽失真（最大）:- 上升/下降时间（典型值）:- 电压 - 电源:3 V ~ 5.5 V，4.5 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商器件封装:16-SOIC 标准包装:50 |
| IL356 | 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:HIGH VOLTAGE SOLID STATE RELA OPTOCOUPLER |
| IL358 | 功能描述:高线性光耦合器 Linear for Optical DAA in Telecomm RoHS:否 制造商:Avago Technologies 输入类型:AC/DC 最大正向二极管电压:1.95 V 最大反向二极管电压:2.5 V 最大输入二极管电流:25 mA 最大功率耗散:60 mW 最大工作温度:+ 100 C 最小工作温度:- 55 C 封装 / 箱体:DIP-8 Gull Wing 封装:Tube |
| IL358_11 | 制造商:IKSEMICON 制造商全称:IK Semicon Co., Ltd 功能描述:Low Power Dual Operational Amplifier |
发布紧急采购，3分钟左右您将得到回复。