- 您现在的位置：买卖IC网 > PDF目录21449 > IL710-3E (NVE Corp/Isolation Products)ISOLATOR HS MAGN DIGITAL 8SOIC PDF资料下载
参数资料
| 型号： | IL710-3E |
| 厂商： | NVE Corp/Isolation Products |
| 文件页数： | 6/14页 |
| 文件大小： | 0K |
| 描述： | ISOLATOR HS MAGN DIGITAL 8SOIC |
| 产品培训模块： | IsoLoop® Isolator |
| 产品目录绘图： | IL710 Circuit |
| 标准包装： | 100 |
| 系列： | IsoLoop® |
| 输入 - 1 侧/2 侧： | 1/0 |
| 通道数： | 1 |
| 电源电压： | 3 V ~ 5.5 V |
| 电压 - 隔离： | 2500Vrms |
| 数据速率： | 110Mbps |
| 传输延迟： | 12ns |
| 输出类型： | 三态 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC（窄型） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 100°C |
| 产品目录页面： | 2771 (CN2011-ZH PDF) |
| 其它名称： | 390-1057-5 |
IL710
Application Information
Electrostatic Discharge Sensitivity
This product has been tested for electrostatic sensitivity to the
limits stated in the specifications. However, NVE recommends that
all integrated circuits be handled with appropriate care to avoid
damage. Damage caused by inappropriate handling or storage could
range from performance degradation to complete failure.
Electromagnetic Compatibility
IsoLoop Isolators have the lowest EMC footprint of any isolation
technology. IsoLoop Isolators’ Wheatstone bridge configuration
and differential magnetic field signaling ensure excellent EMC
performance against all relevant standards.
These isolators are fully compliant with generic EMC standards
EN50081, EN50082-1 and the umbrella line-voltage standard for
Information Technology Equipment (ITE) EN61000. NVE has
completed compliance tests in the categories below:
EN50081-1
Residential, Commercial & Light Industrial
Methods EN55022, EN55014
EN50082-2: Industrial Environment
Methods EN61000-4-2 (ESD), EN61000-4-3 (Electromagnetic
Field Immunity), EN61000-4-4 (Electrical Transient Immunity),
EN61000-4-6 (RFI Immunity), EN61000-4-8 (Power Frequency
Magnetic Field Immunity), EN61000-4-9 (Pulsed Magnetic
Field), EN61000-4-10 (Damped Oscillatory Magnetic Field)
ENV50204
Power Supply Decoupling
Both power supplies to these devices should be decoupled with low
ESR 47 nF ceramic capacitors. Ground planes for both GND 1 and
GND 2 are highly recommended for data rates above 10 Mbps.
Capacitors must be located as close as possible to the V DD pins.
Signal Status on Start-up and Shut Down
To minimize power dissipation, input signals are differentiated and
then latched on the output side of the isolation barrier to reconstruct
the signal. This could result in an ambiguous output state
depending on power up, shutdown and power loss sequencing.
Therefore, the designer should consider including an initialization
signal in the start-up circuit. Initialization consists of toggling the
input either high then low, or low then high.
Data Transmission Rates
The reliability of a transmission system is directly related to the
accuracy and quality of the transmitted digital information. For a
digital system, those parameters which determine the limits of the
data transmission are pulse width distortion and propagation delay
skew.
Propagation delay is the time taken for the signal to travel through
the device. This is usually different when sending a low-to-high
than when sending a high-to-low signal. This difference, or error, is
called pulse width distortion (PWD) and is usually in nanoseconds.
It may also be expressed as a percentage:
Radiated Field from Digital Telephones (Immunity Test)
Immunity to external magnetic fields is even higher if the field
direction is “end-to-end” rather than to “pin-to-pin” as shown in the
diagram below:
PWD% = Maximum Pulse Width Distortion (ns)
Signal Pulse Width (ns)
For example, with data rates of 12.5 Mbps:
PWD% = 3 ns
x 100% = 3.75%
80 ns
x 100%
This figure is almost three times better than any available
optocoupler with the same temperature range, and two times better
than any optocoupler regardless of published temperature range.
IsoLoop isolators exceed the 10% maximum PWD recommended
by PROFIBUS, and will run to nearly 35 Mb within the 10% limit.
Propagation delay skew is the signal propagation difference
Cross-axis Field Direction
Dynamic Power Consumption
IsoLoop Isolators achieve their low power consumption from the
way they transmit data across the isolation barrier. By detecting the
edge transitions of the input logic signal and converting these to
narrow current pulses, a magnetic field is created around the GMR
Wheatstone bridge. Depending on the direction of the magnetic
field, the bridge causes the output comparator to switch following
the input logic signal. Since the current pulses are narrow, about
2.5 ns, the power consumption is independent of mark-to-space
ratio and solely dependent on frequency. This has obvious
advantages over optocouplers, which have power consumption
heavily dependent on mark-to-space ratio.
6
between two or more channels. This becomes significant in clocked
systems because it is undesirable for the clock pulse to arrive
before the data has settled. Short propagation delay skew is
therefore especially critical in high data rate parallel systems for
establishing and maintaining accuracy and repeatability. Worst-
case channel-to-channel skew in an IL700 Isolator is only 3 ns,
which is ten times better than any optocoupler. IL700 Isolators
have a maximum propagation delay skew of 6 ns, which is five
times better than any optocoupler.
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
Phone: (952) 829-9217
Fax: (952) 829-9189
www.IsoLoop.com
?NVE Corporation
相关PDF资料 |
PDF描述 |
|---|---|
| 1-1879471-9 | RES 33 OHM 300W 5% WW WIRE |
| A40-LCG-T-R | IC SOCKET STRAIGHT 40POS GOLD |
| IL510-1E | IC DGTL ISOL 1CH 2MBPS 8-MSOP |
| 1-1879471-8 | RES 27 OHM 300W 5% WW WIRE |
| ICO-316-LTT | CONN IC SOCKET 16POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IL710-3E | 制造商:NVE Corporation 功能描述:Digital Isolator |
| IL710S-1E | 功能描述:ISOLATOR HS MAG DGTL 100C 8-MSOP RoHS:是 类别:隔离器 >> 数字隔离器 系列:IsoLoop® 标准包装:66 系列:iCoupler® 输入 - 1 侧/2 侧:2/2 通道数:4 电源电压:3.3V，5V 电压 - 隔离:2500Vrms 数据速率:25Mbps 传输延迟:60ns 输出类型:逻辑 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:管件 工作温度:-40°C ~ 105°C |
| IL710S-3E | 功能描述:ISOLATOR HS MAG DGTL 100C 8-SOIC RoHS:是 类别:隔离器 >> 数字隔离器 系列:IsoLoop® 产品培训模块:IsoLoop® Isolator 标准包装:50 系列:IsoLoop® 输入 - 1 侧/2 侧:5/0 通道数:5 电源电压:3 V ~ 5.5 V 电压 - 隔离:2500Vrms 数据速率:110Mbps 传输延迟:12ns 输出类型:CMOS 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 工作温度:-40°C ~ 85°C 其它名称:390-1053-5 |
| IL710T | 制造商:未知厂家 制造商全称:未知厂家 功能描述:T-Series Wide Temperature Range High Speed Digital Coupler |
| IL710T-1E | 功能描述:ISOLATOR MAG DIGITAL 125C 8-MSOP RoHS:是 类别:隔离器 >> 数字隔离器 系列:IsoLoop® 产品培训模块:IsoLoop® Isolator 标准包装:50 系列:IsoLoop® 输入 - 1 侧/2 侧:5/0 通道数:5 电源电压:3 V ~ 5.5 V 电压 - 隔离:2500Vrms 数据速率:110Mbps 传输延迟:12ns 输出类型:CMOS 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:管件 工作温度:-40°C ~ 85°C 其它名称:390-1053-5 |
发布紧急采购，3分钟左右您将得到回复。