- 您现在的位置：买卖IC网 > PDF目录175851 > IP3088CX5 (NXP SEMICONDUCTORS) Integrated 2, 4, 6 and 8-channel passive LC-filter network with ESD protection to IEC61000-4-2 level 4 PDF资料下载
参数资料
| 型号： | IP3088CX5 |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 消费家电 |
| 英文描述： | Integrated 2, 4, 6 and 8-channel passive LC-filter network with ESD protection to IEC61000-4-2 level 4 |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PBGA5 |
| 封装： | 0.96 X 1.28 MM, 0.65 MM HEIGHT, GREEN, WLCSP-5 |
| 文件页数： | 3/15页 |
| 文件大小： | 284K |
| 代理商： | IP3088CX5 |
IP3088CX5_CX10_CX15_CX20_1
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 01 — 12 February 2010
11 of 15
NXP Semiconductors
IP3088CX5/CX10/CX15/CX20
2, 4, 6 and 8-channel passive LC-filter network with ESD protection
For further information on temperature profiles, refer to application note AN10365
“Surface mount reflow soldering description”.
9.3.1 Stand off
The stand off between the substrate and the chip is determined by:
The amount of printed solder on the substrate
The size of the solder land on the substrate
The bump height on the chip
The higher the stand off, the better the stresses are released due to TEC (Thermal
Expansion Coefficient) differences between substrate and chip.
9.3.2 Quality of solder joint
A flip-chip joint is considered to be a good joint when the entire solder land has been
wetted by the solder from the bump. The surface of the joint should be smooth and the
shape symmetrical. The soldered joints on a chip should be uniform. Voids in the bumps
after reflow can occur during the reflow process in bumps with high ratio of bump diameter
to bump height, i.e. low bumps with large diameter. No failures have been found to be
related to these voids. Solder joint inspection after reflow can be done with X-ray to
monitor defects such as bridging, open circuits and voids.
9.3.3 Rework
In general, rework is not recommended. By rework we mean the process of removing the
chip from the substrate and replacing it with a new chip. If a chip is removed from the
substrate, most solder balls of the chip will be damaged. In that case it is recommended
not to re-use the chip again.
MSL: Moisture Sensitivity Level
Fig 12. Temperature profiles for large and small components
001aac844
temperature
time
minimum peak temperature
= minimum soldering temperature
maximum peak temperature
= MSL limit, damage level
peak
temperature
相关PDF资料 |
PDF描述 |
|---|---|
| IP3253CZ12-6-TTL | Integrated 4-, 6- and 8-channel passive EMI-filter network with high-level ESD protection |
| IP3253CZ16-8-TTL | Integrated 4-, 6- and 8-channel passive EMI-filter network with high-level ESD protection |
| IP3253CZ8-4-TTL | Integrated 4-, 6- and 8-channel passive EMI-filter network with high-level ESD protection |
| IP3254CZ12-6-TTL | Integrated 4-, 6- and 8-channel passive EMI-filter network with high-level ESD protection |
| IP3254CZ16-8-TTL | Integrated 4-, 6- and 8-channel passive EMI-filter network with high-level ESD protection |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IP3088CX5,135 | 功能描述:信号调节 50Ohm LowPass 3GHz RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel |
| IP3101 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Versatile Gate Driver |
| IP3102L | 制造商:INTERPOINT 制造商全称:INTERPOINT 功能描述:Gate drive IC |
| IP317 | 制造商:SEME-LAB 制造商全称:Seme LAB 功能描述:1.5 AMP POSITIVE ADJUSTABLE VOLTAGE REGULATOR FOR HI-REL APPLICATIONS |
| IP317A | 制造商:SEME-LAB 制造商全称:Seme LAB 功能描述:1.5 AMP POSITIVE ADJUSTABLE VOLTAGE REGULATOR FOR HI-REL APPLICATIONS |
发布紧急采购，3分钟左右您将得到回复。