参数资料
| 型号： | IP82C54 |
| 厂商： | Intersil |
| 文件页数： | 3/22页 |
| 文件大小： | 0K |
| 描述： | IC OSC PROG TIMER 8MHZ 24DIP |
| 标准包装： | 165 |
| 类型： | 可编程计时器 |
| 频率： | 8MHz |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 10mA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 24-DIP（0.600"，15.24mm） |
| 包装： | 管件 |
| 供应商设备封装： | 24-PDIP |
| 安装类型： | 通孔 |
11
82C54
MODE DEFINITIONS
The following are defined for use in describing the operation
of the 82C54.
CLK PULSE -
A rising edge, then a falling edge, in that
order, of a Counter’s CLK input.
TRIGGER -
A rising edge of a Counter’s Gate input.
COUNTER LOADING -
The transfer of a count from the CR
to the CE (See “Functional Description”)
MODE 0: INTERRUPT ON TERMINAL COUNT
Mode 0 is typically used for event counting. After the Control
Word is written, OUT is initially low, and will remain low until
the Counter reaches zero. OUT then goes high and remains
high until a new count or a new Mode 0 Control Word is
written to the Counter.
GATE = 1 enables counting; GATE = 0 disables counting.
GATE has no effect on OUT.
After the Control Word and initial count are written to a
Counter, the initial count will be loaded on the next CLK
pulse. This CLK pulse does not decrement the count, so for
an initial count of N, OUT does not go high until N + 1 CLK
pulses after the initial count is written.
If a new count is written to the Counter it will be loaded on
the next CLK pulse and counting will continue from the new
count. If a two-byte count is written, the following happens:
1. Writing the first byte disables counting. Out is set low
immediately (no clock pulse required).
2. Writing the second byte allows the new count to be
loaded on the next CLK pulse.
This allows the counting sequence to be synchronized by
software. Again OUT does not go high until N + 1 CLK
pulses after the new count of N is written.
COMMANDS
DESCRIPTION
RESULT
D7
D6
D5
D4
D3
D2
D1
D0
1
0
1
0
Read-Back Count and Status of Counter 0
Count and Status Latched for Counter 0
1
0
1
0
Read-Back Status of Counter 1
Status Latched for Counter 1
1
0
1
0
Read-Back Status of Counters 2, 1
Status Latched for Counter 2,
But Not Counter 1
1
0
1
0
Read-Back Count of Counter 2
Count Latched for Counter 2
1
0
1
0
Read-Back Count and Status of Counter 1
Count Latched for Counter 1,
But Not Status
1
0
1
0
Read-Back Status of Counter 1
Command Ignored, Status Already
Latched for Counter 1
FIGURE 7. READ-BACK COMMAND EXAMPLE
CS
RD
WR
A1
A0
01000
Write into Counter 0
01001
Write into Counter 1
01010
Write into Counter 2
01011
Write Control Word
00100
Read from Counter 0
00101
Read from Counter 1
00110
Read from Counter 2
00111
No-Operation (Three-State)
1
XXXX
No-Operation (Three-State)
0
1
X
No-Operation (Three-State)
FIGURE 8. READ/WRITE OPERATIONS SUMMARY
相关PDF资料 |
PDF描述 |
|---|---|
| CS82C54-12 | IC OSC PROG TIMER 12MHZ 28PLCC |
| VE-BTP-MX-B1 | CONVERTER MOD DC/DC 13.8V 75W |
| VE-B4B-IU-F1 | CONVERTER MOD DC/DC 95V 200W |
| VE-BTN-MX-B1 | CONVERTER MOD DC/DC 18.5V 75W |
| VE-B44-IU-F3 | CONVERTER MOD DC/DC 48V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IP82C54/+ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Timer Circuit |
| IP82C54-10 | 功能描述:计时器和支持产品 PERIPH PRG-CNTR 5V 10MHZ 24PDIP IND RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| IP82C54-10S5001 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| IP82C54-10Z | 功能描述:计时器和支持产品 W/ANNEAL PERIPH PRG- CNTR 5V 10MHZ 24PDIP RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| IP82C54-12 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:CMOS Programmable Interval Timer |
发布紧急采购，3分钟左右您将得到回复。