- 您现在的位置：买卖IC网 > PDF目录1808 > IR3081AMTRPBF (International Rectifier)IC CTRLR XPHASE VR10.0 28MLPQ PDF资料下载
参数资料
| 型号： | IR3081AMTRPBF |
| 厂商： | International Rectifier |
| 文件页数： | 16/39页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR XPHASE VR10.0 28MLPQ |
| 标准包装： | 1 |
| 系列： | XPhase™ |
| 应用： | 处理器 |
| 电流 - 电源： | 11mA |
| 电源电压： | 9.5 V ~ 14 V |
| 工作温度： | 0°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-MLPQ |
| 供应商设备封装： | 28-MLPQ（5x5） |
| 包装： | 标准包装 |
| 产品目录页面： | 1381 (CN2011-ZH PDF) |
| 其它名称： | IR3081AMPBFDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
IR3081APBF
Soft Start, Over-Current Fault Delay, and Hiccup Mode
The IR3081A has a programmable soft-start function to limit the surge current during the converter start-up. A
capacitor connected between the SS/DEL and LGND pins controls soft start as well as over-current protection delay
and hiccup mode timing. A charge current of 70uA and discharge current of 6uA control the up slope and down
slope of the voltage at the SS/DEL pin respectively
Figure 10 depicts the various operating modes as controlled by the SS/DEL function. If there is no fault, the SS/DEL
pin will begin to be charged. The error amplifier output is clamped low until SS/DEL reaches 1.3V. The error
amplifier will then regulate the converter’s output voltage to match the SS/DEL voltage less the 1.3V offset until it
reaches the level determined by the VID inputs. The SS/DEL voltage continues to increase until it rises above 3.71V
and allows the PWRGD signal to be asserted. SS/DEL finally settles at 3.8V, indicating the end of the soft start.
Under Voltage Lock Out and VID=11111x faults as well as a low signal on the ENABLE input immediately sets the
fault latch causing SS/DEL to begin to discharge. The SS/DEL capacitor will continue to discharge down to 0.2V. If
the fault has cleared the fault latch will be reset by the discharge comparator allowing a normal soft start to occur.
A delay is included if an over-current condition occurs after a successful soft start sequence. This is required since
over-current conditions can occur as part of normal operation due to load transients or VID transitions. If an over-
current fault occurs during normal operation it will initiate the discharge of the capacitor at SS/DEL but will not set
the fault latch immediately. If the over-current condition persists long enough for the SS/DEL capacitor to discharge
below the 90mV offset of the delay comparator, the Fault latch will be set pulling the error amplifier’s output low
inhibiting switching in the phase ICs and de-asserting the PWRGD signal. The SS/DEL capacitor will continue to
discharge until it reaches 0.2V and the fault latch is reset allowing a normal soft start to occur. If an over-current
condition is again encountered during the soft start cycle the fault latch will be set without any delay and hiccup
mode will begin. During hiccup mode the charge to discharge current ratio results in a fixed 7.9% hiccup mode duty
cycle regardless of at what point the over-current condition occurs. However, the hiccup frequency is determined by
the load current and over-current set value.
The over-current delay can be reduced by adding a resistor in series with the SS/DEL capacitor. The delay
comparator’s offset voltage is reduced by the drop in the resistor caused by the discharge current. The value of the
series resistor should be 10K ? or less to avoid interference with the soft start function.
If SS/DEL pin is pulled below 0.9V, the converter can be disabled.
Under Voltage Lockout (UVLO)
The UVLO function monitors the IR3081A’s VCC supply pin and ensures that IR3081A has a high enough voltage
to power the internal circuit. The IR3081A’s UVLO is set higher than the minimum operating voltage of compatible
Phase ICs thus providing UVLO protection for them as well. During power-up the fault latch is reset when VCC
exceeds 9.7V and there is no other fault. If the VCC voltage drops below 8.9V the fault latch will be set. For
converters using a separate 5V supply for gate driver bias an external UVLO circuit can be added to prevent any
operation until adequate voltage is present. A diode connected between the 5V supply and the SS/DEL pin provides
a simple 5V UVLO function.
Over Current Protection (OCP)
The current limit threshold is set by a resistor connected between the OCSET and VDAC pins. If the IIN pin voltage,
which is proportional to the average current plus DAC voltage, exceeds the OCSET voltage, the over-current
protection is triggered.
VID = 11111X Fault
VID codes of 111111 and 111110 will set the fault latch and disable the error amplifier. An 800ns delay is provided
to prevent a fault condition from occurring during Dynamic VID changes.
Enable Input
Pulling the ENABLE pin below 0.6V sets the Fault Latch.
Page 16 of 39
1/31 /05
相关PDF资料 |
PDF描述 |
|---|---|
| IR3081MPBF | IC PHASE CONTROLLER 28MLPQ |
| IR3081M | IC PHASE CONTROLLER 28-MLPQ |
| IR3082AMTRPBF | IC XPHASE CONTROL 9.6V 20-MLPQ |
| IR3082MTRPBF | IC CTLR XPHASE 20-MLPQ |
| IR3084AMPBF | IC XPHASE CONTROL 28-MLPQ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IR3081M | 功能描述:IC PHASE CONTROLLER 28-MLPQ RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:XPhase™ 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| IR3081MPBF | 功能描述:IC PHASE CONTROLLER 28MLPQ RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:XPhase™ 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| IR3081MTR | 功能描述:IC PHASE CONTROLLER 28L MLPQ RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:XPhase™ 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| IR3081MTRPBF | 功能描述:IC PHASE CONTROLLER 28-MLPQ RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:XPhase™ 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| IR3082 | 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE AMD OPTERON/ATHLON 64 CONTROL IC |
发布紧急采购，3分钟左右您将得到回复。