参数资料
| 型号： | IR3081MPBF |
| 厂商： | International Rectifier |
| 文件页数： | 21/40页 |
| 文件大小： | 0K |
| 描述： | IC PHASE CONTROLLER 28MLPQ |
| 标准包装： | 100 |
| 系列： | XPhase™ |
| 应用： | 处理器 |
| 电流 - 电源： | 11mA |
| 电源电压： | 9.5 V ~ 14 V |
| 工作温度： | 0°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-MLPQ |
| 供应商设备封装： | 28-MLPQ（5x5） |
| 包装： | 剪切带 (CT) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
IR3081PBF
Over Temperature Setting Resistors R HOTSET1 and R HOTSET2
The threshold voltage of VRHOT comparator is proportional to the die temperature T J (oC) of phase IC. Determine
the relationship between the die temperature of phase IC and the temperature of the power converter according to
the power loss, PCB layout and airflow etc, and then calculate HOTSET threshold voltage corresponding to the
allowed maximum temperature from Equation (20).
V HOTSET = 4 . 73 * 10 * T J + 1 . 241
? 3
(20)
There are two ways to set the over temperature threshold, central setting and local setting. In the central setting,
only one resistor divider is used, and the setting voltage is connected to HOTSET pins of all the phase ICs. To
reduce the influence of noise on the accuracy of over temperature setting, a 0.1uF capacitor should be placed next
to HOTSET pin of each phase IC. In the local setting, a resistor divider per phase is needed, and the setting voltage
is connected to HOTSET pin of each phase. The 0.1uF decoupling capacitor is not necessary. Use VBIAS as the
reference voltage. If R HOTSET1 is pre-selected, R HOTSET2 can be calculated as follows.
R HOTSET 2 =
R HOTSET 1 ? V HOTSET
V BIAS ? V HOTSET
(21)
Phase Delay Timing Resistors R PHASE1 and R PHASE2
The phase delay of the interleaved multiphase converter is programmed by the resistor divider connected at
RMPIN+ or RMPIN- depending on which slope of the oscillator ramp is used for the phase delay programming of
phase IC, as shown in Figure 3.
If the upslope is used, RMPIN+ pin of the phase IC should be connected to RMPOUT pin of the control IC and
RMPIN- pin should be connected to the resistor divider. When RMPOUT voltage is above the trip voltage at
RMPIN- pin, the PWM latch is set. GATEL becomes low, and GATEH becomes high after the non-overlap time.
If down slope is used, RMPIN- pin of the phase IC should be connected to RMPOUT pin of the control IC and
RMPIN+ pin should be connected to the resistor divider. When RMPOUT voltage is below the trip voltage at
RMPIN- pin, the PWM latch is set. GATEL becomes low, and GATEH becomes high after the non-overlap time.
Use VBIAS voltage as the reference for the resistor divider since the oscillator ramp magnitude from control IC
tracks VBIAS voltage. Try to avoid both edges of the oscillator ramp for better noise immunity. Determine the ratio
of the programming resistors corresponding to the desired switching frequencies and phase numbers. If the resistor
R PHASEx1 is pre-selected, the resistor R PHASEx2 is determined as:
R PHASEx 2 =
RA PHASEx ? R PHASEx 1
1 ? RA PHASEx
(22)
Combined Over Temperature and Phase Delay Setting Resistors R PHASE1 , R PHASE2 and R PHASE3
The over temperature setting resistor divider can be combined with the phase delay resistor divider to save one
resistor per phase.
Calculate the HOTSET threshold voltage V HOTSET corresponding to the allowed maximum temperature from
Equation (20). If the over temperature setting voltage is lower than the phase delay setting voltage,
VBIAS*RA PHASEx , connect RMPIN+ or RMPIN- pin between R PHASEx1 and R PHASEx2, and connect HOTSET pin
between R PHASEx2 and R PHASEx3 . Pre-select R PHASEx1 ,
Page 21 of 40
R PHASEx 2 =
R PHASEx 3 =
( RA PHASEx ? V BIAS ? V HOTSET ) * R PHASEx 1
V BIAS ? ( 1 ? RA PHASEx )
V HOTSET ? R PHASEx 1
V BIAS * ( 1 ? RA PHASEx )
(23)
(24)
10/01 /04
相关PDF资料 |
PDF描述 |
|---|---|
| IR3081M | IC PHASE CONTROLLER 28-MLPQ |
| IR3082AMTRPBF | IC XPHASE CONTROL 9.6V 20-MLPQ |
| IR3082MTRPBF | IC CTLR XPHASE 20-MLPQ |
| IR3084AMPBF | IC XPHASE CONTROL 28-MLPQ |
| IR3084MTRPBF | IC CTLR XPHASE 28-MLPQ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IR3081MTR | 功能描述:IC PHASE CONTROLLER 28L MLPQ RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:XPhase™ 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| IR3081MTRPBF | 功能描述:IC PHASE CONTROLLER 28-MLPQ RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:XPhase™ 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| IR3082 | 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE AMD OPTERON/ATHLON 64 CONTROL IC |
| IR3082AMPBF | 功能描述:IC XPHASE CONTROL 9.6V 20-MLPQ RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:XPhase™ 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| IR3082AMTRPBF | 功能描述:开关变换器、稳压器与控制器 9.6V 5Bit VID 300mV XPHASE CTRL IC RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。