参数资料
型号: IR3082AMPBF
厂商: International Rectifier
文件页数: 5/33页
文件大小: 0K
描述: IC XPHASE CONTROL 9.6V 20-MLPQ
标准包装: 100
系列: XPhase™
应用: 处理器
电流 - 电源: 12mA
电源电压: 8.05 V ~ 16 V
工作温度: 0°C ~ 100°C
安装类型: 表面贴装
封装/外壳: 20-MLPQ
供应商设备封装: 20-MLPQ(5x5)
包装: 剪切带 (CT)
IR3082A
IR3082
ERROR
AMP
EAOUT
FB
RFB
OCSET
+
+
"FAST"
ISOURCE
VDAC
-
-
ISINK
VDAC
VDAC
BUFFER
AMP
IOFFSET IROSC
IROSC IOCSET
RVDAC
SYSTEM
SET POINT
VOLTAGE
ROSC
CVDAC
CURRENT
SOURCE
GENERATOR
BUFFER
AMP
+
ROSC
1.2V
ROSC
-
VOSNS-
Figure 1 – System Set Point Test Circuit
PIN DESCRIPTION
PIN#
1-5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PIN SYMBOL
VID4-0
VOSNS-
ROSC
VDAC
OCSET
IIN
VDRP
FB
EAOUT
VBIAS
VCC
LGND
RMPOUT
SS/DEL
PWRGD
ENABLE
PIN DESCRIPTION
Inputs to VID D to A Converter.
Remote Sense Input. Connect to ground at the Load.
Connect a resistor to VOSNS- to program oscillator frequency and OCSET, FB, and
VDAC bias currents.
Regulated voltage programmed by the VID inputs. Connect an external RC network
to VOSNS- to program Dynamic VID slew rate and provide compensation for the
internal Buffer Amplifier.
Programs the hiccup over-current threshold through an external resistor tied to
VDAC and an internal current source. Over-current protection can be disabled by
connecting a resistor from this pin to VDAC to program the threshold higher than the
possible signal into the IIN pin from the Phase ICs but no greater than 5V (do not
float this pin as improper operation will occur.)
Current Sense input from the Phase IC(s). If current feedback from the Phase ICs is
not required for implementing droop or over-current protection connect to the LGND
pin. To ensure proper operation do not float this pin.
Buffered IIN signal. Connect an external RC network to FB to program converter
output impedance.
Inverting input to the Error Amplifier. Converter output voltage is offset from the
VDAC voltage through an external resistor connected to the converter output voltage
at the load and an internal current source.
Output of the Error Amplifier.
6.8V/5mA Regulated output used as a system reference voltage for internal circuitry
and the Phase ICs.
Power Input for internal circuitry.
Local Ground for internal circuitry and IC substrate connection.
Oscillator Output voltage. Used by Phase ICs to program Phase Delay
Controls Converter Start-up and Over-Current Timing. Connect an external capacitor
to LGND to program.
Open Collector output that drives low during Start-Up and any external fault
condition. Connect external pull-up.
Enable Input. A logic low applied to this pin puts the IC into Fault mode. Do not float
this pin as the logic state will be undefined.
Page 5 of 33
05/02/2006
相关PDF资料
PDF描述
GCE15DHRR CONN CARD EXTEND 30POS 1MM SLD
M3AAA-3436J IDC CABLE - MSC34A/MC34G/MSC34A
REC5-4809DRW/H6/A CONV DC/DC 5W 36-72VIN +/-09VOUT
GBE15DHRR CONN CARD EXTEND 30POS 1MM SLD
RBM18DCSN-S288 CONN EDGECARD 36POS .156 EXTEND
相关代理商/技术参数
参数描述
IR3082AMTRPBF 功能描述:开关变换器、稳压器与控制器 9.6V 5Bit VID 300mV XPHASE CTRL IC RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
IR3082M 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE AMD OPTERON/ATHLON 64 CONTROL IC
IR3082MPBF 功能描述:IC XPHASE CONTROL 20-MLPQ RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:XPhase™ 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像,声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP(8x8) 包装:管件
IR3082MPBF 制造商:International Rectifier 功能描述:Controller IC Package/Case:20-MLPQ
IR3082MTR 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE AMD OPTERON/ATHLON 64 CONTROL IC