参数资料
| 型号： | IR3084MTRPBF |
| 厂商： | International Rectifier |
| 文件页数： | 17/45页 |
| 文件大小： | 0K |
| 描述： | IC CTLR XPHASE 28-MLPQ |
| 产品变化通告： | (EP) Parts Discontinuation 25/May/2012 |
| 标准包装： | 3,000 |
| 系列： | XPhase™ |
| 应用： | 处理器 |
| 电流 - 电源： | 14mA |
| 电源电压： | 9.5 V ~ 16 V |
| 工作温度： | 0°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-MLPQ |
| 供应商设备封装： | 28-MLPQ（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页
IR3084
Inductor DCR Temperature Correction
If the thermal compensation of the inductor DCR provided by the temperature dependent gain of the current
sense amplifier is not adequate, a negative temperature coefficient (NTC) thermistor can be used for additional
correction. The thermistor should be placed close to the inductor and connected in parallel with the feedback
resistor, as shown in Figure 9. The resistor in series with the thermistor is used to reduce the nonlinearity of the
thermistor.
Control IC
VDAC
RSETPT
VSETPT
EAOUT
RFB
Vo
IOFFSET
Error
Amplifier
AVP
Amplifier
VDRP
RFB2
RDRP
Rt
-
+
IIN
Figure 9 ? Temperature compensation of inductor DCR
Remote Voltage Sensing
To compensate for impedance in the ground plane, the VOSNS ? pin is used for remote sensing and connects
directly to the load. The VDAC voltage is referenced to VOSNS ? to avoid additional error terms or delay related
to a separate differential amplifier. The capacitor connecting the VDAC and VOSNS ? pins ensure that high speed
transients are fed directly into the error amp without delay.
Start-up Modes
The IR3084 has a programmable soft-start function to limit the surge current during the converter start-up. A
capacitor connected between the SS/DEL and LGND pins controls soft start as well as over-current protection
delay and hiccup mode timing. A charge current of 70uA controls the positive slope of the voltage at the SS/DEL
pin.
There are two types of start-up possible: Boot Mode (VR11) and Non-Boot Mode (legacy VR10). In Boot Mode,
the soft start circuitry will initially set the voltage at the VDAC pin to 1.1V and the converter’s output will slowly
rise, using the slew rate set by the capacitor at the SS/DEL pin, until it’s equal to 1.1V. After Vcore achieves the
1.1V Boot voltage, there will be a short delay, the VID pins will be sampled, and the voltage at the VDAC pin and
the converter’s output will increase or decrease to the desired VID setting using the dynamic VID slew rate. In
Non-Boot Mode, the soft start sequence will ramp the voltage at the VDAC pin directly to the external VID setting
using the slew rate set by the capacitor at the SS/DEL pin without pausing at the 1.1V Boot voltage.
Page 17 of 45
03/4/2009
相关PDF资料 |
PDF描述 |
|---|---|
| IR3084UMPBF | IC XPHASE CONTROL 28-MLPQ |
| IR3086AMPBF | IC PHASE CONTROLLER OVP 20MLPQ |
| IR3086MPBF | IC CONTROLLER PHASE 20MLPQ |
| IR3087MPBF | IC XPHASE W/OVP/TM CTRL 20MLPQ |
| IR3087M | IC XPHASE W/OVP/TM CTRL 20-MLPQ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IR3084U | 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASETM VR10, VR11 & OPTERON/ATHLON64 CONTROL IC |
| IR3084UMPBF | 功能描述:IC XPHASE CONTROL 28-MLPQ RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:XPhase™ 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| IR3084UMTRPBF | 功能描述:开关变换器、稳压器与控制器 VR10 VR11 Athlon64 XPHASE CTRL IC RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| IR3086 | 制造商:IRF 制造商全称:International Rectifier 功能描述:PHASE IC WITH OVP, FAULT AND OVERTEMP DETECT |
| IR3086A | 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASETM PHASE IC WITH OVP, FAULT AND OVERTEMP DETECT |
发布紧急采购，3分钟左右您将得到回复。