参数资料
型号: IR3832WMTR1PBF
厂商: International Rectifier
文件页数: 27/32页
文件大小: 0K
描述: IC REG SYNC BUCK 4A DDR 15-QFN
特色产品: Gen2.1 SupIRBuck? Integrated Voltage Regulators
标准包装: 1
系列: SupIRBuck™
应用: 转换器,DDR
输入电压: 1.5 V ~ 16 V
输出数: 1
输出电压: 0.6 V ~ 14.4 V
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 15-PowerVQFN
供应商设备封装: PQFN(5x6)
包装: 标准包装
其它名称: IR3832WMTR1PBFDKR
PD-97508
IR3832WMPbF
Layout Considerations
Vin
PGnd
PGnd
capacitor at the Sw pin.
AGnd Vout
The layout is very important when designing high
frequency switching converters. Layout will affect
noise pickup and can cause a good design to
perform with less than expected results.
Make all the connections for the power
components in the top layer with wide, copper
filled areas or polygons. In general, it is desirable
to make proper use of power planes and
polygons for power distribution and heat
dissipation.
The inductor, output capacitors and the IR3832W
should be as close to each other as possible.
This helps to reduce the EMI radiated by the
power traces due to the high switching currents
through them. Place the input capacitor directly at
the Vin pin of IR3832W.
The feedback part of the system should be kept
away from the inductor and other noise sources.
The critical bypass components such as
capacitors for Vcc should be close to their
respective pins. It is important to place the
feedback components including feedback
resistors and compensation components close to
The connection between the OCSet resistor and
the Sw pin should not share any trace with the
connection between the bootstrap capacitor and
the Sw pin. Instead, it is recommended to use a
Kelvin connection of the trace from the OCSet
resistor and the trace from the bootstrap
Vin
VoutAGnd
In a multilayer PCB use one layer as a power
ground plane and have a control circuit ground
(analog ground), to which all signals are
referenced. The goal is to localize the high
current path to a separate loop that does not
interfere with the more sensitive analog control
function. These two grounds must be connected
together on the PC board layout at a single point.
The Power QFN is a thermally enhanced
package. Based on thermal performance it is
recommended to use at least a 4-layers PCB. To
effectively remove heat from the device the
exposed pad should be connected to the ground
plane using vias. Figure 26 illustrates the
implementation of the layout guidelines outlined
above, on a 4 layer board.
Fb and Comp pins.
Enough copper &
minimum length
ground path between
Input and Output
Compensation parts
PGnd
should be placed as close
as possible to
the Comp pin .
Vin
All bypass caps
should be placed as
close as possible to
their connecting
Resistors Rt and
Rocset should be
placed as close as
possible to their pins.
AGnd
AGnd
Vin
PGnd
Vout
Vout
pins.
Fig. 26a. IR3832W layout
considerations – Top Layer
Rev 6.0
27
相关PDF资料
PDF描述
GBA43DTKH CONN EDGECARD 86POS DIP .125 SLD
VI-JTZ-CY-S CONVERTER MOD DC/DC 2V 20W
25ZLJ3300M16X25 CAP ALUM 3300UF 25V 20% RADIAL
VE-J3V-EX-F1 CONVERTER MOD DC/DC 5.8V 75W
GBA43DTKD CONN EDGECARD 86POS DIP .125 SLD
相关代理商/技术参数
参数描述
IR3832WMTRPBF 功能描述:直流/直流开关调节器 4A SupIRBuck Reg 250-1500kHz, 1.5-16V RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
IR3837MPBF 制造商:IRF 制造商全称:International Rectifier 功能描述:HIGHLY INTEGRATED 14A SINGLE-INPUT VOLTAGE, SYNCHRONOUS BUCK REGULATOR
IR3837MTR1PBF 功能描述:直流/直流开关调节器 14A SupIRBuck Reg 250-1500kHz, 1.5-16V RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
IR3837MTR1PBF 制造商:International Rectifier 功能描述:IC DC-DC CONV 1.5 MHz QFN-17 制造商:International Rectifier 功能描述:IC, DC-DC CONV, 1.5 MHz, QFN-17
IR3837MTR1PBF-CUT TAPE 制造商:IR 功能描述:IR3837 Series 1.5 MHz 14 A Surface Mount Synchronous Buck Regulator - QFN-16