参数资料
| 型号： | IRADK31 |
| 厂商： | International Rectifier |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | DESIGN KIT 1/4 HP DC FOR IR31XX |
| 标准包装： | 80 |
| 系列： | iMOTION™ |
| 主要目的： | 电源管理，电机控制 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | IR3101，IR3103，IR3104 |
| 主要属性： | 3-Ph BLDC 1/3 HP，120 ~ 230 VAC |
| 次要属性： | GUI 驱动或独立式，过电流保护，光隔离 RS-232， |
| 已供物品： | 板，CD，样品 |
| 相关产品： | IR3103-ND - PWR MOD 180W GATE DRIVER 11-SIP IR3101-ND - IC POWER MODULE 1.6A 500V 11-SIP |
I R A D K 3 1
This is the voltage selector switch to set the correct rectifier configuration to the AC input.
Prior to connection the system to the AC input, carefully check the position of SW1.
Set to 115V when applying power from 110/120VAC source, or set to 230V when
applying power from a 220/230VAC source.
Output Phases Terminal (J6)
This is the terminal for motor connection, output from 3-phase inverter circuit driven by
PWM signals to the motor (i.e. motor voltages). These signals are referenced to the
negative DC power rail, which is NOT a ground potential.
CAUTION: Beware of electric shock hazard. DO NOT connect any grounded test
equipment such as an Oscilloscope to these test terminals. Always isolate your
equipment from Earth Ground.
Connect the motor phase inputs (U, V, and W) from this terminal as depicted in Figure 2.
Hall Sensor connector (JP1)
This is Motor’s Hall Sensors feedback connector that allows for detecting the rotor state
and position.
RS-232 Port (J5)
A standard 9-pin D-shell female type connector (DB9F) that provides an Opto-isolated RS-
232 serial link with the PC to control and monitor the development board.
RS-232 Serial Link:
A standard 9-pin D Female connector is used for the RS-232 serial link. The pins used on
this connector are the RxD, TxD, GND, RTS, and DTR. The RTS and DTR signals provide
sufficient current to drive the Opto-couplers. The current drawn from these pins is far
below permissible limits for the RS-232 drivers.
The GUI should work with any of the available COM ports on the PC. There is no
restriction on COM port. COM1 is the GUI’s default port. The serial cable may be
connected or disconnected (With no AC power applied to the controller) at any time without
having to restart your computer.
A USB 2.0 to Serial Adapter (P/N: USB-2920) is available from www.cables4computer.com
may be used as an option. Ensure that the port selection in the GUI is set to COM3 with
Baud Rate at 9600 when using this adapter.
www.irf.com
7
相关PDF资料 |
PDF描述 |
|---|---|
| IRAUDAMP1 | KIT REFERENCE DESIGN W/IR2011S |
| IRAUDAMP4 | KIT 2CH 120W HALF BRDG AUDIO AMP |
| IRCS2277S | DEMO FOR 3-PHASE/380V MOTOR DRV |
| IRDC2085S-DF | BOARD EVAL CONV DC BUS W/IRF6603 |
| IRDC3038 | KIT W/IRU3038 PWM CTRL DDR 14-PI |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IRADK-S10UP60 | 制造商:International Rectifier 功能描述: |
| IRAE410 | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES |
| IRA-E410 | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES |
| IRA-E410QW1 | 制造商:Murata Manufacturing Co Ltd 功能描述:PYROELECTRIC INFRARED SENSOR - Bulk |
| IRA-E410S1 | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES |
发布紧急采购，3分钟左右您将得到回复。