参数资料
| 型号： | IRADK31 |
| 厂商： | International Rectifier |
| 文件页数： | 8/24页 |
| 文件大小： | 0K |
| 描述： | DESIGN KIT 1/4 HP DC FOR IR31XX |
| 标准包装： | 80 |
| 系列： | iMOTION™ |
| 主要目的： | 电源管理，电机控制 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | IR3101，IR3103，IR3104 |
| 主要属性： | 3-Ph BLDC 1/3 HP，120 ~ 230 VAC |
| 次要属性： | GUI 驱动或独立式，过电流保护，光隔离 RS-232， |
| 已供物品： | 板，CD，样品 |
| 相关产品： | IR3103-ND - PWR MOD 180W GATE DRIVER 11-SIP IR3101-ND - IC POWER MODULE 1.6A 500V 11-SIP |
I R A D K 3 1
MPLAB ICD2 Connector (J4)
A 6-wire RJ-11 jack is provided as a programming or In-Circuit Debugger interface. This
will also allow users to use development tools, such as MPLAB ICD2, while the board is
under power. Note that this connector is referenced to the –DC Bus.
LEDs D10, D11, and SW2, SW3, R28
At initial power on, LEDs D10 (Red) and D11 (Green) blink on and off at a fixed rate.
Rotating potentiometer R28 can change the blinking rate. Clockwise (CW) slows the
blinking rate and counterclockwise (CCW) increases the blinking rate. When R28 is near
the end position on CCW, both LEDs may look like they are on all the time because they
are blinking at a faster rate. The functions of D10, D11, SW2, SW3, and R28 are as
follows:
Stand-alone Mode (Also referred as Manual mode):
- Green LED: Indicates the Hall sensors level, 3 hall sensors combined when the motor
rotates. If the motor shaft is rotated by hand, this LED will blink on and off.
- Red LED: In normal operation indicates the direction of rotation command. On for
forward, Off for reverse. It will blink on and off, if hardware over current fault condition
occurs (using the last downloaded parameters).
- SW2: This switch is used to toggle between Run and Stop.
- SW3: This switch is used to toggle between Forward and Reverse.
- R28: Used to control the Motor speed.
PC Mode (Also referred as GUI mode):
- Green LED: Indicates the Hall sensors level, 3 hall sensors combined when the motor
rotates. If the motor shaft is rotated by hand, this LED will blink on and off.
- Red LED: In normal operation indicates the direction of rotation command. On for
forward, Off for reverse. It will blink on and off if an over current fault condition occurs.
- SW2, SW3: They are not used in PC Mode. GUI command is used instead.
- R28: Not used with this mode.
Test Points (TP1 – TP5)
These test points are used for voltage and signal monitoring purposes.
TP1, TP2: For monitoring the +DC Bus and –DC Bus, respectively
? TP3: Current Feedback signal.
? TP4: +15V auxiliary power supply.
? TP5: +5V auxiliary power supply.
Jumper (J2)
This is the reset jumper to the microcontroller. When shorted, it resets the microcontroller
and starts the firmware from beginning. This jumper is default to open.
www.irf.com
8
相关PDF资料 |
PDF描述 |
|---|---|
| IRAUDAMP1 | KIT REFERENCE DESIGN W/IR2011S |
| IRAUDAMP4 | KIT 2CH 120W HALF BRDG AUDIO AMP |
| IRCS2277S | DEMO FOR 3-PHASE/380V MOTOR DRV |
| IRDC2085S-DF | BOARD EVAL CONV DC BUS W/IRF6603 |
| IRDC3038 | KIT W/IRU3038 PWM CTRL DDR 14-PI |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IRADK-S10UP60 | 制造商:International Rectifier 功能描述: |
| IRAE410 | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES |
| IRA-E410 | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES |
| IRA-E410QW1 | 制造商:Murata Manufacturing Co Ltd 功能描述:PYROELECTRIC INFRARED SENSOR - Bulk |
| IRA-E410S1 | 制造商:MURATA 制造商全称:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES |
发布紧急采购，3分钟左右您将得到回复。