- 您现在的位置：买卖IC网 > PDF目录1811 > IRU3007CWTR (International Rectifier)IC CTRL/REG SYNC BUCK 28-SOIC PDF资料下载
参数资料
| 型号： | IRU3007CWTR |
| 厂商： | International Rectifier |
| 文件页数： | 5/17页 |
| 文件大小： | 0K |
| 描述： | IC CTRL/REG SYNC BUCK 28-SOIC |
| 标准包装： | 1,000 |
| 应用： | 控制器，Intel Pentium? II |
| 输入电压： | 5V，12V |
| 输出数： | 4 |
| 输出电压： | 1.3 V ~ 3.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 带卷 (TR) |
IRU3007
PIN#
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
PIN SYMBOL
Fb2
V5
SS
Fault / Rt
Fb4
V SEN 2
V OUT 4
Gnd
Gate3
Fb3
NC
Fb1
V SEN 1
OCSet1
PGnd
LGate1
Phase1
UGate1
V12
PIN DESCRIPTION
This pin provides the feedback for the non-synchronous switching regulator. A resistor
divider is connected from this pin to V OUT 2 and ground that sets the output voltage. The
value of the resistor connected from V OUT 2 to Fb2 must be less than 100 V .
5V supply voltage. A high frequency capacitor (0.1 to 1 m F) must be placed close to this
pin and connected from this pin to the ground plane for noise free operation.
This pin provides the soft-start for the 2 switching regulators. An internal resistor charges
an external capacitor that is connected from 5V supply to this pin which ramps up the
outputs of the switching regulators, preventing the outputs from overshooting as well as
limiting the input current. The second function of the Soft-Start cap is to provide long off
time (HICCUP) for the synchronous MOSFET during current limiting.
This pin has dual function. It acts as an output of the OVP circuitry or it can be used to
program the frequency using an external resistor. When used as a fault detector, if any of
the switcher outputs exceed the OVP trip point, the Fault pin switches to 12V and the
soft-start cap is discharged. If the Fault pin is to be connected to any external circuitry,
it needs to be buffered as shown in the application circuit.
This pin provides the feedback for the internal LDO regulator that its output is V OUT 4.
This pin is connected to the output of the I/O switching regulator. It is an input that
provides sensing for the Under/Over-voltage circuitry for the I/O supply as well as the
power for the internal LDO regulator.
This pin is the output of the internal LDO regulator.
This pin serves as the ground pin and must be connected directly to the ground plane.
This pin controls the gate of an external transistor for the 1.5V GTL+ linear regulator.
This pin provides the feedback for the linear regulator that its output drive is Gate3.
No connection.
This pin provides the feedback for the synchronous switching regulator. Typically this pin
can be connected directly to the output of the switching regulator. However, a resistor
divider is recommended to be connected from this pin to V OUT 1 and ground to adjust the
output voltage for any drop in the output voltage that is caused by the trace resistance.
The value of the resistor connected from V OUT 1 to Fb1 must be less than 100 V .
This pin is internally connected to the undervoltage and overvoltage comparators sensing
the Vcore status. It must be connected directly to the Vcore supply.
This pin is connected to the Drain of the power MOSFET of the Core supply and it
provides the positive sensing for the internal current sensing circuitry. An external resis-
tor programs the CS threshold depending on the R DS of the power MOSFET. An external
capacitor is placed in parallel with the programming resistor to provide high frequency
noise filtering.
This pin serves as the Power ground pin and must be connected directly to the ground
plane close to the source of the synchronous MOSFET. A high frequency capacitor
(typically 1 m F) must be connected from V12 pin to this pin for noise free operation.
Output driver for the synchronous power MOSFET for the Core supply.
This pin is connected to the Source of the power MOSFET for the Core supply and it
provides the negative sensing for the internal current sensing circuitry.
Output driver for the high-side power MOSFET for the Core supply.
This pin is connected to the 12V supply and serves as the power Vcc pin for the output
drivers. A high frequency capacitor (typically 1 m F) must be placed close to this pin and
PGnd pin and be connected directly from this pin to the ground plane for noise free
operation.
Rev. 2.1
08/20/02
www.irf.com
5
相关PDF资料 |
PDF描述 |
|---|---|
| IRU3011CWTR | IC CTRL SYNC BUCK 5BIT 20SOIC(W) |
| IRU3013CWTR | IC CNTRL BUCK W/TRPL LDO 24-SOIC |
| IRU3018CWTR | IC CTRL/REG SYNC BUCK 24-SOIC |
| IRU3021MCWTR | IC CTRL/REG SYNC BUCK 28-SOIC |
| IRU3027CWTR | IC CTRL/REG SYNC BUCK 28-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IRU3008CWTR | 功能描述:IC REG 24-SOIC(W) RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:20 系列:SIMPLE SWITCHER® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:12V 输入电压:4 V ~ 60 V PWM 型:电压模式 频率 - 开关:52kHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 包装:管件 供应商设备封装:16-DIP 其它名称:*LM2575HVN-12LM2575HVN-12 |
| IRU3010CW | 制造商:International Rectifier 功能描述:SWITCHING CONTROLLER |
| IRU3010CWTR | 功能描述:IC REG BUCK SYNC 20SOIC(W) RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:20 系列:SIMPLE SWITCHER® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:12V 输入电压:4 V ~ 60 V PWM 型:电压模式 频率 - 开关:52kHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 包装:管件 供应商设备封装:16-DIP 其它名称:*LM2575HVN-12LM2575HVN-12 |
| IRU3011 | 制造商:IRF 制造商全称:International Rectifier 功能描述:5-BIT PROGRAMMABLE SYNCHRONOUS BUCK CONTROLLER IC |
| IRU3011CW | 功能描述:IC CTRL SYNC BUCK 5BIT 20-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。